4000-seriesSmart-deadbolt

Home Access Smart Deadbolt 4000 Series

Set up, program and troubleshoot the Philips Home Access Smart Deadbolt 4000 series: installation, PIN and fingerprint codes, Auto-Lock, modes and reset.
Supporting Models: 4000 series
English, French

Read The User Manual (PDF) Online

View the original document directly below. For safety-critical procedures, follow the manufacturer’s instructions for your exact model.

Philips Home Access Smart Deadbolt 4000 Series

The Philips Home Access Smart Deadbolt 4000 series is a battery-powered deadbolt that you can open with a PIN code on its touchscreen keypad, a fingerprint, a backup mechanical key, or the Philips Home Access app on your phone. It runs on four AA alkaline batteries and stores up to 100 User PIN Codes and 50 fingerprints. Beyond basic locking and unlocking, it offers Auto-Lock, One-Touch Locking, Silent Mode, Away Mode and Privacy Mode, and it can work with an optional Door Position Sensor that reports whether the door is open or closed. Lock activity records, temporary PIN codes, guest sharing and voice assistant control are available through the app, and a Philips Wi-Fi Bridge (sold separately) adds real-time record updates, Away Mode notifications and voice assistant support.

Safety Notes and Cautions

Safety

  • Damage caused by not following the instructions is not covered by the warranty.
  • Use only components supplied by the manufacturer and the accessories it suggests.
  • Use only AA alkaline batteries.
  • Do not forcibly disassemble the lock to trigger an alarm or damage it.
  • Do not scrape the fingerprint sensor with sharp objects, because this may cause permanent damage.
  • Do not remove the batteries during lock setup and operation.
  • Change the default Master PIN Code immediately after installation, either on the lock or in the Philips Home Access app.

Cautions

  • Do not place the batteries near fire sources.
  • Do not connect the two poles of the batteries to metals. This avoids a short circuit and a potential explosion.
  • Replacement components must be handled by Philips, a Philips-authorized service center, or a professional technician.
  • Do not use parts or accessories made by other manufacturers, except batteries.
  • Do not expose the product to places with water leakage or splashing.

Returns and Disposal

Locks can be returned to an authorized Philips service center, and appropriate compensation is provided if the returned product meets Philips’ conditions. Follow local regulations and do not throw used products or batteries into normal household waste.

Parts and Controls

What Is in the Box

ItemQuantity / note
Exterior Assembly1
Latch Bolt1
Mounting Plate1
Interior Assembly1
AA Batteries4
Battery Cover1
Interior Assembly Screws2
Mounting Plate Screws2
Reinforcement PlateOptional
Strike Plate1
Strike Plate Screws2
Reinforcement Plate Screws2, optional
Latch Bolt Screws2
Upper Screw and Screw PostOptional
Backup Keys2
Drive-In CollarOptional
Drilling Template1
Door Position Sensor and Door Position Sensor CapCap is optional
Door Position Sensor Screws2, optional
Door Position Sensor Mounting Template1
User Manual and Quick Start Guide1 each

Exterior Controls

No.PartWhat it is
1Status IndicatorLight bar above the keypad
2Touchscreen KeypadDigits 0–9 for PIN codes
3Cancel KeyThe ✗ key
4Confirm KeyThe ✓ key
5Fingerprint SensorReads registered fingerprints
6Keyhole CoverCovers the keyhole
7KeyholeFor the backup mechanical key

Interior Controls

No.PartWhat it does
1Battery CoverCovers the four AA batteries; the ESN and QR code are on its back
2Reset ButtonActivates lock handing and performs the factory reset
3Privacy ButtonLocks the door from inside; hold it for 3 seconds for Privacy Mode
4Installation BuckleUsed to detach and attach the Interior Assembly during installation
5Thumb TurnLocks and unlocks the deadbolt from inside

Door Requirements Before Installation

Check these measurements before you start. A #2 Phillips screwdriver is the only required tool.

CheckRequired value
Hole in the door face1-1/2″ or 2-1/8″ (38 mm or 54 mm)
Hole in the door edge1″ (25 mm)
Backset2-3/8″ or 2-3/4″ (60 mm or 70 mm)
Door thickness1-3/8″ to 2″ (35 mm to 50 mm)
Hole depth in the door frameMinimum 1″ (25 mm), so the deadbolt can extend into the frame when the door is locked

Make sure the door frame is aligned with the door and that nothing obstructs the door frame.

How to Install the Lock

Optional Upper Screw Preparation

The Upper Screw is optional. It adds security or helps when a door is weak or warped. If you plan to use it, drill a 19/32″ hole in the door before you begin installing, using the Drilling Template.

Set the Backset and Install the Latch Bolt

  1. Hold the Latch Bolt in front of the door hole with its face flush against the door edge. Check whether the slotted hole is centered in the door hole.
  2. If the slot is centered, no adjustment is needed. If it is not centered, rotate and pull the Latch Bolt to extend it to the 2-3/8″ (60 mm) or 2-3/4″ (70 mm) setting.
  3. Install the Latch Bolt with the Latch Bolt Screws if the door edge is chiseled. If it is not chiseled, install it with the Drive-In Collar as illustrated in the four-step drawing.
  4. Use a screwdriver to confirm that the deadbolt locks and unlocks smoothly.
  5. Install the Strike Plate on the door frame with the Strike Plate Screws. The hole in the door frame must be drilled at least 1″ (25 mm) deep.

Install the Exterior Assembly

Before you begin, make sure the Latch Bolt is fully retracted (unlocked position). Do not insert the key while installing.

  1. Measure the hole in the door. If it is 1-1/2″ (38 mm), remove the spacer. If it is 2-1/8″ (54 mm), go straight to the next step.
  2. With the Latch Bolt fully retracted, route the cable below the Latch Bolt and insert the tailpiece through the slot in the Latch Bolt.
  3. Move the Installation Buckles on both sides of the Interior Assembly upward and remove the Mounting Plate from the interior base.
  4. Secure the Mounting Plate with the Mounting Plate Screws, keeping it parallel to the door edge. Do not overtighten the screws, and route the cable through the hole in the Mounting Plate.

If you are using the optional Upper Screw, fasten the Screw Post into the hole of the Exterior Assembly before installing the Upper Screw.

Install the Interior Assembly

  1. Push the Battery Cover up in the direction illustrated. Do not load batteries until lock installation is finished.
  2. Insert the Exterior Assembly cable connector into the socket on the Interior Assembly and push firmly until it is completely attached.
  3. Keep the Thumb Turn in the vertical position, toggle the Installation Buckle upward, and install the Interior Assembly.
  4. Attach the Interior Assembly to the Mounting Plate, toggle the Installation Buckle downward, and fasten it with the Interior Assembly Screws. Do not use other screws.
  5. Install the AA alkaline batteries following the direction guide inside the battery holder.
  6. Press and hold the Reset Button for at least 5 seconds until you hear a beep. This activates lock handing and must be completed before you set up the lock.

Make sure the cable is not pinched, or the lock will not function properly.

Door Position Sensor

The Door Position Sensor comprises a cover, a mounting housing, a magnet, mounting tape, a mounting template, optional mounting screws (2) and an optional cap. It can be installed as a Surface Mount or a Flush Mount, and Surface Mount is the recommended method. Follow the Door Position Sensor Mounting Template in the box for the specific steps.

If you want to use the sensor without drilling into the door frame, install the surface-mounted version using the Mounting Tape only.

Set Up the Lock with the Philips Home Access App

  1. Scan the QR code on the setup page with your phone to download the Philips Home Access app (App Store or Google Play).
  2. Register and log in to the app.
  3. Turn on Bluetooth on your phone and tap Add device in the app.
  4. Scan the QR code, or enter the ESN manually. Both are on the back of the Battery Cover.
  5. Complete the pairing steps shown in the app.
  6. Follow the in-app instructions to calibrate the lock and the Door Position Sensor together. Do this near the smart lock.

If the app fails to calibrate the lock, check that the Door Position Sensor is installed correctly and try again.

Features and Modes

Master PIN Code

The Master PIN Code is needed to program and adjust settings. It can also unlock the deadbolt in Away Mode and Privacy Mode. The default is 12345678, and it must be changed right after installation. The owner or manager should keep it confidential.

Ways to Unlock

You can unlock with a fingerprint, a PIN code, a key, or a gentle touch in the Philips Home Access app. Fingerprints and PIN codes can be added on the lock or in the app.

App-Based Features

  • Simple Sharing: Tap “add guest” in the app to share access with family or friends. Access can be shared and accepted only through the app.
  • Lock Activities Insight: A record of lock and unlock events and user access. Records update whenever your smartphone is connected to the lock by Bluetooth, or in real time with the Philips Wi-Fi Bridge (sold separately).
  • Temporary PIN Codes: Generate PIN codes remotely for guests or a service technician. A code can be one-time (deleted upon use) or valid repeatedly during a set period.

One-Touch Locking

Press and hold any key on the touchscreen for 2 seconds to lock the door.

Auto-Lock

After the lock has been unlocked, it locks automatically. This feature is disabled by default. On the lock, the delay can be set between 30 and 180 seconds. In the app it can be set between 10 and 180 seconds.

Silent Mode

Silent Mode mutes the sounds when you press the keypad. Low battery warnings and system alerts still sound. Enable it on the lock or in the app.

Away Mode

Away Mode is meant for vacations or long trips. It restricts all User PIN Codes and fingerprints until the Master PIN Code is entered on the keypad. If the lock is unlocked with the Thumb Turn, an alarm sounds for 1 minute, and a notification is sent through the app when the Philips Wi-Fi Bridge (sold separately) is installed. Entering the Master PIN Code on the keypad, or changing the setting in the app, disables the alarm and Away Mode.

Privacy Mode

Press and hold the Privacy Button on the Interior Assembly for 3 seconds. This restricts all User PIN Code and fingerprint access. Privacy Mode turns off automatically after you unlock the door with the Thumb Turn or the Master PIN Code.

Default Settings and Factory Reset

A factory reset erases all user and network settings and unpairs the lock from users’ accounts. All paired accessories are removed too, and the lock handing process is activated again. To reset, press the Reset Button for at least 5 seconds until you hear the tone that prompts you to restore default settings.

FunctionDefault setting
Master PIN Code12345678
Auto-LockDisabled
Silent ModeDisabled
Shut Down Time3 minutes
Away ModeDisabled

PIN and Fingerprint Rules

  • Master PIN Code: 4 to 10 digits.
  • User PIN Code: 4 to 10 digits, with a total of 100 stored in the lock.
  • User Fingerprint: 50 fingerprints can be stored.
  • Change the default Master PIN Code before programming any other codes.
  • Master and User PIN Codes cannot be a forward sequence (such as 12345678), a backward sequence (such as 87654321) or a repeated digit (such as 22222222).
  • A new code also cannot contain an existing code. For example, if 5683 is already saved, then 568391 and 915683 are rejected.

Programming on the Lock

If no button is pressed for more than 10 seconds, the lock exits programming mode. The indicator light flashes red when a code you entered was not saved successfully. Everything below can also be done in the Philips Home Access app.

Every menu starts the same way: press ✗ twice, enter the Master PIN Code, then press ✓ once. The green light comes on. Then continue as shown.

TaskContinue with
Change the default Master PIN CodeEnter the new Master PIN Code, press ✓, re-enter it, press ✓
Change the Master PIN Code laterPress 1, enter the new Master PIN Code, press ✓, re-enter it, press ✓
Add a User PIN CodePress 2, enter the new User PIN Code, press ✓, re-enter it, press ✓
Delete a User PIN CodePress 3, enter the unwanted User PIN Code, press ✓
Add a User FingerprintPress 4, then scan the fingerprint 8 times. Each successful scan is confirmed by a green light
Delete a User FingerprintPress 5, then scan the unwanted fingerprint once
Change the system languagePress 6, then press 1 for English, 2 for French or 3 for Spanish, then ✓. Option 4 in this menu is Silent Mode
Set Timed Auto-LockPress 7, then press 1 for Auto-Lock off, 2 for 30 s, 3 for 60 s, 4 for 120 s or 5 for 180 s, then ✓
Enable Away ModePress 8, then press ✓

To improve fingerprint recognition, register your finger from different angles during the 8-scan process.

Locking and Unlocking

Unlocking from Outside

  1. Enter a PIN code and press ✓.
  2. Use a registered fingerprint.
  3. Use the mechanical key.
  4. Use the Philips Home Access app.

Unlocking from Inside

  1. Rotate the Thumb Turn to the unlocked position.
  2. Use the Philips Home Access app.
  3. Use a voice assistant, when the Philips Wi-Fi Bridge (sold separately) is installed.

Locking from Outside

  1. Press and hold any keypad button for at least 2 seconds to lock in Manual Mode.
  2. In Auto-Lock mode, the Latch Bolt extends automatically after the door has been unlocked and then shut.
  3. Use the Philips Home Access app.
  4. Use the mechanical key.

Locking from Inside

  1. Rotate the Thumb Turn to the locked position to lock in Manual Mode.
  2. Press the Privacy Button to lock in Manual Mode.
  3. In Auto-Lock Mode, the lock engages automatically.
  4. Use the Philips Home Access app.
  5. Use a voice assistant, when the Philips Wi-Fi Bridge (sold separately) is installed.

Troubleshooting

ProblemWhat to do
Latch Bolt does not operate correctly after installationConfirm the backset on the Latch Bolt is set to the right length. Confirm the Latch Bolt was retracted before installation. Restore factory defaults and enter the default Master PIN Code to set up the lock.
After installation, the Latch Bolt makes sounds but does not workRe-install and reset the lock. Make sure the Latch Bolt is fully retracted (unlocked) before installing the assemblies, and do not insert the key during installation. Check that the Exterior Assembly cable connector is correctly seated in the Interior Assembly socket. Keep both assemblies aligned and parallel to the door edge, with the Latch Bolt parallel to the door edge. Press and hold the Reset Button for at least 5 seconds until you hear a beep. Use 4 new AA dry batteries, not rechargeable ones, and never mix new batteries with old ones.
Door handing is not activated after the batteries are installedPress the Reset Button for at least 5 seconds until you hear the tone prompting you to restore default settings.
The lock turns in the wrong directionPress and hold the Reset Button for at least 5 seconds until you hear a beep to activate lock handing. If that does not solve it, the lock is probably not installed correctly, so re-install and reset it.
Cannot pull the key out of the keyholeDisassemble the lock, rotate it to pull out the key, and re-install the lock. Do not insert the key during installation.
The lock rotates only if the key is insertedMake sure the Latch Bolt is installed correctly.
The lock does not lock or unlock smoothly with the Thumb TurnConfirm the Mounting Screws are properly installed.
The lock only locks but does not unlock, or the Latch Bolt goes in and out uncontrollablyIf the door locks and unlocks smoothly while open, the door frame is the problem: make sure its hole is at least 1″ (25 mm) deep. If the problem also occurs with the door open, hold the Reset Button for at least 5 seconds until you hear a beep. If resetting fails, re-install the lock and reset it again. If nothing works, contact support.
Failed to lockKeep the Exterior and Interior Assemblies aligned and parallel to the door edge, and keep the Latch Bolt parallel to the door edge.
The Master PIN Code cannot be changedRestore factory settings and reprogram all user PIN codes.
Failed to scan the QR code on the deviceScan in a well-lit place, use your phone’s flashlight, or find sufficient lighting. Keep enough distance between the phone and the QR code and keep the code in the center of the screen. Direct light or sunlight can cause reflections that interfere with scanning.
Failed to add the device via BluetoothMake sure the lock has enough power and your phone is close to it. Check that Bluetooth is turned on. On Android, enable Location Service.
Failed to set up the lockMake sure the lock is installed correctly. Insert fresh batteries and make sure the cable is not pinched. After installation, reset the lock to factory settings to complete setup.
I forgot my Master PIN CodePerform a factory reset. All PIN codes are deleted and the Master PIN Code returns to 12345678.
Cannot add fingerprints, or a fingerprint does not workMake sure the fingerprint is registered and recognizable. Change the default Master PIN Code before adding fingerprints. Keep both your finger and the Fingerprint Sensor dry and clean. Add multiple fingerprints of the same finger, or try other fingers. Register from different angles and press harder during the 8 scans.
Receiving low battery alertsRemove the batteries and insert 4 new AA alkaline batteries.
The keypad is not respondingCheck that the batteries are inserted correctly. If the battery indicator flashes continuously, the batteries are low, so replace them with 4 new AA alkaline batteries. Make sure the cable is properly connected and was not damaged during installation.
Auto-Lock is not workingIf the battery indicator flashes continuously, replace the batteries with 4 new AA alkaline batteries. Make sure Auto-Lock is activated, on the lock or in the app.
The app shows the door as open when it is closedRe-calibrate the lock with the door position sensor in the app. If that does not help, check whether another magnet has been brought into the range of the lock and remove it.

Warranty, Support and Regulatory Notes

The lock carries a 2-year warranty. For the warranty terms that apply to your purchase, visit www.philips.com or contact the dealer where you bought it. Register your product and get support at www.philips.com/support. In the U.S.A. and Canada, you can also call +1 (833) 599-9111.

The product is manufactured by and sold under the responsibility of Shenzhen Conex Intelligent Technology Co., Ltd., which is the warrantor. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V., used under license.

The lock complies with Part 15 of the FCC Rules as a Class B digital device and with Canadian CAN ICES-3 (B)/NMB-3(B). Install and operate it with at least 20 cm between the radiator and your body.

Frequently Asked Questions

What is the default Master PIN Code, and how do I change it?

The default Master PIN Code is 12345678, and it should be changed right after installation. On the lock, press ✗ twice, enter 12345678, and press ✓. When the green light comes on, enter your new Master PIN Code (4 to 10 digits), press ✓, re-enter it, and press ✓ again. You can also change it in the Philips Home Access app. If the light flashes red, the code was not saved, and the lock leaves programming mode after 10 seconds without a key press.

How do I factory reset the lock?

Press and hold the Reset Button on the Interior Assembly for at least 5 seconds, until you hear the tone prompting you to restore the default settings. The reset erases all user and network settings, unpairs the lock from users’ accounts, removes all paired accessories and reactivates lock handing. Afterward the Master PIN Code is back to 12345678, and Auto-Lock, Silent Mode and Away Mode are disabled.

What can I do if I forgot my Master PIN Code?

Perform a factory reset. This is the only recovery step offered for a forgotten Master PIN Code, and it deletes every PIN code, so you will need to set a new Master PIN Code and add your User PIN Codes and fingerprints again.

How many PIN codes and fingerprints can the lock store, and which codes are rejected?

The lock stores 100 User PIN Codes and 50 fingerprints. All PIN codes are 4 to 10 digits. The lock rejects forward sequences such as 12345678, backward sequences such as 87654321, repeated digits such as 22222222, and any new code that contains an existing code. For example, if 5683 is saved, neither 568391 nor 915683 will be accepted.

How do I add a fingerprint?

Change the default Master PIN Code first, because the lock expects that before fingerprints are added. Then press ✗ twice, enter the Master PIN Code, press ✓, press 4, and scan the finger 8 times. A green light confirms each successful scan. Lift and reposition the finger between scans so it is registered from different angles, and keep both the finger and the sensor clean and dry. If a finger still fails, try registering the same finger more than once or use another finger.

How do I turn on Auto-Lock?

Auto-Lock is disabled by default. On the lock, press ✗ twice, enter the Master PIN Code, press ✓, press 7, then press 2, 3, 4 or 5 for a delay of 30, 60, 120 or 180 seconds and press ✓. Pressing 1 instead turns Auto-Lock off. In the Philips Home Access app, the delay can be set anywhere from 10 to 180 seconds. Once on, the Latch Bolt extends by itself after the door has been unlocked and shut.

How do I lock the door from outside without my phone?

Press and hold any key on the touchscreen keypad for at least 2 seconds, which locks the door in Manual Mode. If Auto-Lock is on, the Latch Bolt extends by itself after you unlock the door and close it. The mechanical key also locks the door from outside.

What should I do if the keypad stops responding or I get low battery alerts?

First check that the four AA batteries are inserted in the right direction. A continuously flashing battery indicator means the batteries are low, so replace all four with new AA alkaline batteries. Do not use rechargeable batteries or mix new and old ones. If the keypad still does not respond, confirm the cable between the Exterior and Interior Assemblies is properly connected and was not damaged during installation.

Why can’t I add the lock to the app through Bluetooth?

Make sure the lock has enough power, keep your phone close to it, and confirm Bluetooth is turned on. On an Android phone, Location Service must also be enabled. If the QR code on the back of the Battery Cover will not scan, try a well-lit place or your phone’s flashlight, keep the code centered on the screen, and avoid direct light or sunlight that causes reflections. You can enter the ESN printed there by hand instead.

What is the difference between Away Mode and Privacy Mode?

Away Mode is for longer absences. It blocks all User PIN Codes and fingerprints until the Master PIN Code is entered, and unlocking with the Thumb Turn sounds an alarm for 1 minute. To turn it on at the lock, press ✗ twice, enter the Master PIN Code, press ✓, press 8, and press ✓. Privacy Mode is a temporary lockout from inside: hold the Privacy Button for 3 seconds to block all User PIN Code and fingerprint access. It ends automatically when you unlock with the Thumb Turn or the Master PIN Code.

Why does the app say the door is open when it is closed?

Re-calibrate the lock with the Door Position Sensor in the Philips Home Access app, standing near the lock. If the reading is still wrong, check whether another magnet has been placed within range of the lock and remove it. If calibration fails altogether, confirm the sensor was installed correctly and try again.

Can I mute the keypad sounds or change the lock’s language?

Yes. To change the language, press ✗ twice, enter the Master PIN Code, press ✓, press 6, then press 1 for English, 2 for French or 3 for Spanish, and press ✓. Silent Mode, which mutes keypad sounds, is the fourth option in the same menu and can also be set in the app. Even in Silent Mode, low battery warnings and system alerts still sound.

Found something that needs correcting?

If a model number, instruction, specification, or document link looks incorrect, please send us the page URL and relevant details.