Philips Home Access Electronic Deadbolt
The Philips Home Access electronic deadbolt replaces a standard deadbolt with a lock you can open in several ways: a touchscreen keypad for PIN codes, a fingerprint sensor, a mechanical backup key, or a thumb turn on the inside. It runs on four AA alkaline batteries and stores one Master PIN code, up to 20 user PIN codes and up to 50 fingerprints. Optional settings include Auto Lock with a 30 to 180 second delay, Silent Mode, Away Mode and Privacy Mode, and the Philips Home Access App can generate One Time User Codes. The lock can be installed with a #2 Phillips screwdriver on prepared doors that meet the dimensions listed below.
Parts and Controls
What Comes With the Lock
The package contains the following items:
| No. | Item |
| 1 | Exterior Keypad Assembly |
| 2 | Latch Bolt |
| 3 | Mounting Plate |
| 4 | Interior Assembly |
| 5 | AA Batteries (4) |
| 6 | Battery Cover |
| 7 | Interior Assembly Screws (2) |
| 8 | Mounting Plate Screws (2) |
| 9 | Reinforcement Plate (Optional) |
| 10 | Strike Plate |
| 11 | Strike Plate Screws (2) and Reinforcement Plate Screws (Optional) (2) |
| 12 | Latch Bolt Screws (2) |
| 13 | Exterior Assembly Screw (Optional) |
| 14 | Backup Keys |
| 15 | Drive-In Collar (Optional) |
| 16 | Drilling Template |
| 17 | User Manual |
| 18 | Quick Start Guide |
Exterior Assembly Controls
| No. | Control |
| 1 | Status Indicator |
| 2 | Touchscreen Keypad |
| 3 | Cancel Key |
| 4 | Confirm Key |
| 5 | Fingerprint |
| 6 | Keyhole Cover |
| 7 | Keyhole |
Interior Assembly Controls
| No. | Control |
| 1 | Battery Cover |
| 2 | Reset Button |
| 3 | Privacy Button |
| 4 | Installation Buckle |
| 5 | Thumb Turn |
Safety and Care
Read and understand all instructions before using the product. Damage caused by failing to follow the instructions is not covered by the warranty.
- Only use the manufacturer-provided components and suggested accessories.
- Only use AA alkaline batteries.
- Do not forcibly disassemble the product to trigger an alarm or damage the product.
- Do not scrape the fingerprint sensor with sharp objects, because this may cause permanent damage.
- Do not remove the batteries during lock setup and operation.
- Change the default Master PIN code immediately after completing the installation.
Cautions:
- Do not place the batteries near fire sources.
- Do not use an emergency power supply that does not meet safety requirements.
- Do not connect the 2 poles of the batteries to metals, to avoid a short circuit and potential explosion.
- Any replacement component should be performed by Philips, a Philips authorized service center or a professional technician.
- Do not use parts or accessories manufactured by others, except batteries.
- Do not expose the product to places that have water leakage or splashing.
Returns and Disposal
Locks can be returned at authorized Philips service centers, and appropriate compensation is provided if the returned product meets Philips conditions. Follow local regulations and do not throw used product or batteries into normal household waste.
Installing the Deadbolt
Required Tools
A #2 Phillips screwdriver is the only tool listed.
Check the Door and Door Frame
Confirm these dimensions before you start:
| Item | Required measurement |
| Hole in the door | 1-1/2″ or 2-1/8″ (38 mm or 54 mm) |
| Hole in the door edge | 1″ (25 mm) |
| Backset | 2-3/8″ or 2-3/4″ (60 mm or 70 mm) |
| Door thickness | 1-3/8″ to 2″ (35 mm to 50 mm) |
| Hole in the door frame | Drilled a minimum of 1″ (25 mm) deep, so the deadbolt can extend into the frame when the door is locked |
Attention: Make sure the door frame is aligned with the door and there are no obstructions in the door frame.
Set the Latch Length and Install the Latch Bolt
- Hold the latch in front of the door hole, with the latch face flush against the door edge. Check whether the slotted hole is centered in the door hole.
- If the slotted hole is centered, no adjustment is needed. If it is not centered, rotate and pull the latch to extend it to the correct backset: 2-3/8″ (60 mm) or 2-3/4″ (70 mm).
- Install the latch bolt with the latch screws. If the door edge is chiseled, place the latch with the “up” marking facing up and fasten it with the latch screws. If the door edge is not chiseled, the Drive-In Collar (optional) is used, as shown in the four illustrations in the original instructions.
- Use a screwdriver to confirm that the deadbolt locks and unlocks smoothly.
Install the Strike on the Door Frame
Install the strike plate on the door frame with the strike screws. The reinforcement plate and its two screws are optional. Make sure the hole in the door frame is drilled a minimum of 1″ (25 mm) deep.
Install the Exterior Assembly
Attention: Before installation, make sure the latch is fully retracted (in the unlocked position).
- Check the diameter of the door hole. For a 1-1/2″ (38 mm) hole, remove the spacer. For a 2-1/8″ (54 mm) hole, go straight to the next step.
- With the latch fully retracted, route the cable below the latch and insert the tailpiece through the slot in the latch. The third top post is optional and is used for additional security or when a door is weak or warped.
- Move the buttons on both sides of the interior assembly upward to remove the mounting plate from the interior base.
- Secure the mounting plate with the Mounting Plate Screws and keep it parallel to the door edge. Do not overtighten the screws. The third screw on top is optional.
Install the Interior Assembly
Attention: Do not load batteries before finishing the lock installation.
- Push the battery cover up in the direction shown in the illustration to remove it.
- Insert the cable connector of the exterior assembly into the socket on the interior assembly. Push the connector in firmly until it is completely attached.
- Keep the thumb turn in the vertical position and install the interior assembly.
- Attach the interior assembly to the mounting plate and fasten it with the Interior Assembly Screws. Do not use other screws.
- Install the AA batteries.
- Press and hold the Reset Button for at least 5 seconds until you hear a beep. This activates the lock handing process, which must be completed before you set up the lock.
Attention: Make sure the cable is not pinched, or the lock will not function properly.
Operating the Lock
Unlock the Door From Outside
- Place your palm over the lock to wake up the keypad.
- Unlock with a PIN code (Master PIN, User PIN or One-Time PIN), with a registered fingerprint, or with the mechanical key.
Unlock the Door From Inside
Rotate the thumb turn to the unlock position.
Lock the Door From Outside
In manual mode, press and hold any button on the keypad for at least 2 seconds to lock the door. In Auto Lock mode, the latch bolt extends automatically after unlocking.
Lock the Door From Inside
In manual mode, rotate the thumb turn to the lock position or press the Privacy Button to lock the door. In Auto Lock mode, the lock locks automatically.
Lock Modes and Settings
Master PIN Code
The Master PIN code is required for programming and adjusting settings. It can also unlock the deadbolt in Away Mode and Privacy Mode. The default is 12345678 and must be changed before programming. The owner or manager should keep it confidential.
Auto Lock
The lock locks itself after it has been unlocked. This function is disabled by default, and the delay can be set between 30 and 180 seconds.
Wrong Code Entry Limit
After 10 unsuccessful attempts to enter a PIN code, the keypad shuts down and is unusable for 3 minutes.
Silent Mode
Keypad sounds can be muted. Low battery warnings and system alerts still sound.
Away Mode
Away Mode is a safety feature for vacations or long trips. It disables all user codes until the Master PIN code is entered on the keypad. If the lock is unlocked with the thumb turn while Away Mode is on, an alarm sounds for 1 minute. Entering the Master PIN code on the keypad disables the alarm and Away Mode.
Privacy Mode
Push and hold the Privacy Button on the inside escutcheon for 3 seconds to activate Privacy Mode. This disables all user PIN code access. Privacy Mode turns off automatically after you unlock the door with the thumb turn or the Master PIN code.
Low Battery Alarm
When the batteries run low, the battery indicator flashes and a voice announces “Low battery. Please replace batteries as soon as possible.” Replace them with four new AA alkaline batteries.
One Time User Code
A One Time User Code is generated by the Philips Home Access App and can be used only once.
PIN Code and Fingerprint Limits
| Item | Limit |
| Master PIN Code | 4 to 10 digits; default 12345678 |
| User PIN Codes | 4 to 10 digits; a total of 20 can be stored |
| User Fingerprints | 50 can be stored |
Master and User PIN codes do not support these number combinations:
- Forward sequences, such as 12345678.
- Backward sequences, such as 87654321.
- Repeated digits, such as 22222222.
- Codes that contain an existing code. If 5683 is already programmed, then 568391 and 915683 are not accepted.
Programming Instructions
Before you program: the default Master PIN code is 12345678, and it should be changed before you program the lock. Touch the keypad with your palm to activate the lock before setting up. The indicator light flashes red when a code you entered was not saved successfully. If no button is pressed for more than 10 seconds, the lock exits programming mode.
Every procedure below starts the same way: press the Cancel key (✕) 2 times, enter the Master PIN code, press the Confirm key (✓) once (the green light turns on), then press the menu number shown.
Change the Master PIN Code
- Press ✕ 2 times, enter the Master PIN code, and press ✓ once. The green light turns on.
- Press 1.
- Enter the new Master PIN code and press ✓ once.
- Re-enter the new Master PIN code and press ✓ once. The green light turns on.
Add a User PIN Code
- Press ✕ 2 times, enter the Master PIN code, and press ✓ once. The green light turns on.
- Press 2.
- Enter the new user PIN code and press ✓ once.
- Re-enter the new user PIN code and press ✓ once. The green light turns on.
Delete a User PIN Code
- Press ✕ 2 times, enter the Master PIN code, and press ✓ once. The green light turns on.
- Press 3.
- Enter the unwanted user PIN code and press ✓ once. The green light turns on.
Add a User Fingerprint
- Press ✕ 2 times, enter the Master PIN code, and press ✓ once. The green light turns on.
- Press 4.
- Scan the fingerprint 8 times. Each successful scan is confirmed by the green light.
Delete a User Fingerprint
- Press ✕ 2 times, enter the Master PIN code, and press ✓ once. The green light turns on.
- Press 5.
- Scan the unwanted fingerprint 1 time. The green light turns on.
Change the System Language
- Press ✕ 2 times, enter the Master PIN code, and press ✓ once. The green light turns on.
- Press 6.
- Press the number for your choice, then press ✓ once. The green light turns on.
| Press | Result |
| 1 | English |
| 2 | French |
| 3 | Spanish |
| 4 | Silent mode |
Set the Timed Auto Lock
- Press ✕ 2 times, enter the Master PIN code, and press ✓ once. The green light turns on.
- Press 7.
- Press the number for your choice, then press ✓ once. The green light turns on.
| Press | Result |
| 1 | Disable Auto Lock |
| 2 | 30 seconds |
| 3 | 60 seconds |
| 4 | 120 seconds |
| 5 | 180 seconds |
Turn On Away Mode
- Press ✕ 2 times, enter the Master PIN code, and press ✓ once. The green light turns on.
- Press 8.
- Press ✓ once. The green light turns on.
Factory Reset and Default Settings
A factory reset deletes all user codes associated with the lock. Restoring the lock also activates the lock handing process. To reset, press and hold the Reset Button on the interior assembly for at least 5 seconds, until you hear the tone prompting you to restore the default settings.
| Setting | Factory default |
| Master PIN Code | 12345678 |
| Auto Lock | Disabled |
| Silent Mode | Disabled |
| Shut Down Time | 3 Minutes |
| Away Mode | Disabled |
Troubleshooting
| Issue | Solution |
| The latch does not operate correctly after installation. | Make sure the backset on the latch is set to the proper length. Make sure the latch bolt was retracted before you installed the deadbolt. Restore the factory default settings and enter the default Master PIN code to set up the lock. |
| The lock does not smoothly lock or unlock while using the thumb turn. | Confirm the proper mounting screws are installed. |
| Lock setup failed. | Make sure the lock is installed correctly. Insert fresh batteries and make sure the cable is not pinched. After installation, reset the lock to factory settings to complete the lock setting process. |
| The keypad is not responding. | Make sure the batteries are inserted correctly. If the battery indicator flashes continuously, the batteries are low, so replace them with four new AA alkaline batteries. Make sure the cable is properly connected and was not damaged during installation. |
| The Master PIN code cannot be changed. | Restore factory settings and reprogram all User PIN codes. |
| I forgot my Master PIN code. | Perform a factory reset to clear all PIN codes. After the reset, all PIN codes are deleted and the Master PIN code returns to the default, 12345678. |
| Auto Lock is not working. | If the battery indicator flashes continuously, replace the batteries with four new AA alkaline batteries. Activate the Auto Lock function as described under Set the Timed Auto Lock. |
| The fingerprint cannot unlock the door. | Make sure the fingerprint is registered and recognizable. |
Warranty and Support
The product comes with a 2-year warranty. It was brought to market by Conex, the manufacturer, and Conex provides the warranty for the product with which the booklet was packaged. For more information on the applicable warranty, visit www.philips.com or contact the dealer where you purchased the product. Product registration and support are available at www.philips.com/support. In the U.S.A. and Canada, call +1 (833) 599-9111.
Frequently Asked Questions
What is the default Master PIN code, and should I change it?
The default Master PIN code is 12345678, and you should change it right after installation, before you program any other codes. The Master PIN code is required for programming and adjusting settings, so keep your new code confidential.
How do I change the Master PIN code?
Touch the keypad with your palm to wake it, press ✕ twice, enter the current Master PIN code and press ✓. When the green light comes on, press 1, enter the new code and press ✓, then enter it again and press ✓ once more. The Master PIN code must be 4 to 10 digits long. If the light flashes red, the code was not saved, so start over. The lock also leaves programming mode if you pause for more than 10 seconds.
How do I add a user PIN code, and which codes will the lock reject?
Press ✕ twice, enter the Master PIN code, press ✓, then press 2. Enter the new 4 to 10 digit code and press ✓, then enter it again and press ✓. The lock rejects forward sequences such as 12345678, backward sequences such as 87654321, repeated digits such as 22222222, and any code that contains an existing code. For example, if 5683 is already stored, 568391 and 915683 will not work.
How many PIN codes and fingerprints can the lock store?
The lock can store one Master PIN code, a total of 20 user PIN codes, and 50 fingerprints. One Time User Codes are generated separately through the Philips Home Access App and work only once.
How do I add a fingerprint?
Press ✕ twice, enter the Master PIN code, press ✓, then press 4. Scan the finger 8 times, and wait for the green light after each successful scan. If a fingerprint later fails to unlock the door, make sure it is registered and recognizable. Do not scrape the sensor with sharp objects, since that can permanently damage it.
How do I delete a user PIN code or fingerprint?
For a PIN code, press ✕ twice, enter the Master PIN code, press ✓, press 3, enter the unwanted user PIN code and press ✓. For a fingerprint, follow the same opening steps, press 5, and scan the unwanted fingerprint once. The green light confirms each deletion.
How do I turn on Auto Lock and choose the delay?
Auto Lock is off by default. To turn it on, press ✕ twice, enter the Master PIN code, press ✓, then press 7. Press 2 for 30 seconds, 3 for 60 seconds, 4 for 120 seconds or 5 for 180 seconds, and finish with ✓. Press 1 and ✓ to disable it again. With Auto Lock on, the latch bolt extends automatically after the door is unlocked. If it stops working, check whether the battery indicator is flashing and replace the batteries with four new AA alkaline batteries if so.
What is Away Mode, and how do I turn it off?
Away Mode is meant for vacations or long trips. It disables all user codes until the Master PIN code is entered on the keypad. To turn it on, press ✕ twice, enter the Master PIN code, press ✓, press 8, and press ✓ again. While it is on, unlocking the door with the thumb turn sounds an alarm for 1 minute. Entering the Master PIN code on the keypad disables both the alarm and Away Mode.
How do I use Privacy Mode?
Press and hold the Privacy Button on the inside of the door for 3 seconds. This disables all user PIN code access. Privacy Mode turns off automatically once you unlock the door with the thumb turn or the Master PIN code.
What happens if I enter the wrong PIN code too many times?
After 10 unsuccessful attempts to enter a PIN code, the keypad shuts down and cannot be used for 3 minutes. Wait for the 3 minutes to pass before trying again.
What should I do if I forgot my Master PIN code?
Perform a factory reset. Press and hold the Reset Button on the interior assembly for at least 5 seconds, until you hear the tone prompting you to restore the default settings. The reset deletes all PIN codes and returns the Master PIN code to 12345678. It also restores Auto Lock, Silent Mode and Away Mode to Disabled, and the lock handing process is activated again. You will need to program your user codes again afterward.
What does the low battery alert mean, and what batteries should I use?
When the batteries run low, the battery indicator flashes and a voice announces “Low battery. Please replace batteries as soon as possible.” Replace all four with new AA alkaline batteries. Silent Mode does not mute this warning. Do not remove the batteries during lock setup and operation, and keep them away from fire sources.
