Philips Lady Shaver Series 6000 BRL159
The Philips BRL159 is a rechargeable, cordless shaver and bikini trimmer for the legs, arms, underarms and bikini area. It is waterproof, so it can be used in the bath or shower and rinsed under the tap. It works on completely dry or completely wet skin. Its flexible shaving head has a contour-following feature and an integrated light. It also comes with a bikini trimming head, a shaving comb and a bikini trimming comb. Both combs trim hair to 0.12 inch/3 mm. The BRL159 is one of nine models covered by this manual, and the differences between them are noted below.
Models and Supplied Accessories
The heads and accessories supplied vary by model. The overview illustration (Fig. 1) assigns them as follows:
| Item | Models |
| Bikini trimming head and bikini trimming comb | BRL137, BRL138, BRL147, BRL149, BRL159 |
| Flexible shaving head with integrated light | BRL129, BRL147, BRL149, BRL159 |
| Standard shaving head | BRL114, BRL127, BRL128, BRL137, BRL138 |
| Exfoliation glove | BRL149, BRL159 |
| Pouch | BRL137, BRL138, BRL147, BRL149, BRL159 |
The illustration does not label the shaving comb or the cleaning brush by model. Check the contents of your own package. Accessory availability may also differ by country.
Parts and Controls
Fig. 1 identifies these parts:
| No. | Part |
| 1 | Bikini trimming comb |
| 2 | Bikini trimming head |
| 3 | Shaving comb |
| 4 | Cutting unit of shaving head |
| 5 | Integrated light |
| 6 | Flexible shaving head with integrated light |
| 7 | Shaving head |
| 8 | Handle |
| 9 | Release button |
| 10 | On/off button |
| 11 | Battery status indicator |
| 12 | Socket for small plug |
| 13 | USB cable |
| 14 | Exfoliation glove |
| 15 | Cleaning brush |
| 16 | Pouch |
The USB power source is not included. A suitable one, such as the Philips HQ87, is available through www.philips.com/support.
Charging
Battery Status Indicator
| Battery status | Indicator |
| Almost empty | Flashing orange light |
| Charging | Flashing white light |
| Fully charged | Solid white light |
About 60 seconds after the battery is fully charged, the indicator switches off automatically. Charge the product before first use and whenever the indicator shows that the battery is almost empty.
Charging Time and Cordless Run Time
| Models | Charging time | Cordless operating time |
| BRL127, BRL128, BRL137, BRL138 | 8 hours | Up to 80 minutes |
| BRL129, BRL147, BRL149, BRL159 | 60 minutes | Up to 100 minutes |
The manual gives no charging time or run time for the BRL114.
How to Charge
Warning: Keep the USB cable and the USB power source dry (Fig. 2).
- Make sure the product is switched off.
- Insert the small plug of the USB cable into the socket in the bottom of the product (Fig. 5).
- Insert the USB plug into the USB power source, which is not included (Fig. 6).
- Insert the USB power source into the power outlet (Fig. 7).
- After charging, remove the USB power source from the power outlet and pull the small plug out of the product.
Charging requires a certified USB power source rated 5 V, ≥ 1 A. To charge safely in a moist environment such as a bathroom, use only an IPX4 (splash-proof) power source. Charge, use and store the product between 50 °F / 10 °C and 95 °F / 35 °C.
Before You Shave
Check the Heads
Before every use, check that the shaving head and trimming head are clean, in good condition and not damaged or worn (Fig. 8). A damaged head can cause skin irritation and reduced performance. If a cutting unit is damaged, throw it away and start using a new one (Fig. 9). You can order a new cutting unit from the Philips website or call Philips support at 1-888-744-5477.
Skin Preparation Tips
- Exfoliate one day before shaving to remove dead skin cells around the hair follicles.
- Clean your skin before you start. If it is wet afterward, pat it dry instead of rubbing.
- Shave before bed so your skin can recover overnight.
- Do not exfoliate within 24 hours before or 48 hours after hair removal, to avoid intensifying possible irritation.
Wet and Dry Use
The product is suitable for both. For easy gliding and comfort, use it on completely wet skin or completely dry skin, not moist skin.
- Dry use: This is the most efficient option. Make sure your skin is clean and completely dry, because dry hairs do not stick to the skin as much.
- Wet use: Make sure your skin is completely wet with water, not just moist. Rinse the shaving head regularly so it keeps gliding smoothly, and gently pat your skin dry afterward. Shaving performance may be better on dry skin.
Using the Product
The product is waterproof (Fig. 3). It is suitable for the bath or shower and for cleaning under the tap. For safety, it can only be used without the cord.
Switching On and Off
| Models | Procedure |
| BRL114, BRL127, BRL128, BRL137, BRL138 | Press the on/off button once to switch the product on or off. |
| BRL129, BRL147, BRL149, BRL159 | Press the on/off button once to switch on. The integrated light goes on automatically (Fig. 10). Press the button again to select the low speed setting. Press it once more to switch off. |
On the BRL129, BRL147, BRL149 and BRL159, you can switch the integrated light off or back on by pressing the on/off button for 2 seconds while the product is switched off. If the attachment produces light, do not point it at open or closed eyes.
Attaching and Detaching Heads
- To detach a head, press the release button at the back of the handle and gently lift the head off (Fig. 11).
- To attach a head, align it with the top of the handle and gently press it down until it clicks into place (Fig. 12).
Switch the product off before removing or attaching any attachment.
Detaching and Attaching the Cutting Unit
Detach the cutting unit for thorough cleaning or to replace a worn one. It is a precision part, so hold it by its plastic housing only (Fig. 13).
- Hold the plastic housing of the cutting unit on both sides and gently pull it out of the shaving head.
- To reattach, align the cutting unit with the shaving head and snap it into place.
Attaching and Detaching the Combs
Shaving comb
- To attach, align the indent in the comb with the notch on the back of the shaving head, then snap the comb on until it clicks (Fig. 14).
- To detach, place a fingernail between the comb and the shaving head to the left or right of the notch on the back. Pull the back of the comb upward (Fig. 15). Do not pull at the sides or teeth.
Bikini trimming comb
- To attach, place the notch on one side of the comb in the indent in the trimming head. Press the comb on until the notch on the other side snaps into the indent on the other side (Fig. 16).
- To detach, place a fingernail between the comb and the trimming head on one side and pull until the comb comes off (Fig. 17). Do not pull at the back or teeth.
Shaving and Trimming
Never use any part of the product on the inner labia (Fig. 4). To shave or trim the outer labia, always attach a comb to the head. Use the product dry for the best result.
- Place the product on your skin so the cutting unit or comb is in full contact with the skin.
- On sensitive areas, stretch the skin with your free hand. For the underarms, raise your arm and put your hand on the back of your head (Fig. 18).
- Move the product slowly against the direction of hair growth. Moving too fast may not give a smooth result.
Shaving Head
The flexible shaving head on the BRL129, BRL147, BRL149 and BRL159 has a contour-following feature for optimal skin contact (Fig. 19). Use the shaving head on the legs, arms, underarms and bikini area, never on the face. Place it flat on the skin (Fig. 20). To shave the outer labia, use it only with the shaving comb attached (Fig. 21). With the shaving comb attached, hair is trimmed to 0.12 inch/3 mm (Fig. 22).
Bikini Trimming Head
Use the trimming head for hard-to-reach areas of the bikini area and for styling and shaping. Place it flat on the skin to trim (Fig. 24). Place it perpendicular to the skin to create different styles (Figs. 25 and 26). To trim the outer labia, use only the trimming head with its comb attached (Fig. 23). With the comb attached, hair is trimmed to 0.12 inch/3 mm (Fig. 27).
Cleaning and Maintenance
Clean the product after each use. Use only cold or lukewarm water. Never use compressed air, scouring pads, abrasive cleaners or aggressive liquids such as gasoline or acetone. Never dry a cutting unit with a towel or tissue, because it can catch in the unit and cause damage.
- Make sure the product is disconnected from the USB cable.
- Switch off the product.
- Remove the cutting unit from the shaving head (Fig. 13) and rinse it under the tap. Do not clean the cutting unit with the brush. The brush is for all other parts and attachments.
- Clean the hair chamber with the brush and rinse it under the tap (Fig. 28).
- Clean all other parts with the brush, then rinse them under the tap.
- Shake off excess water and let all parts air dry completely.
- Place the cutting unit back into the shaving head until it clicks.
For best performance, lubricate the trimmer teeth and foils with a drop of sewing machine oil every six weeks.
Storage
- Make sure the product is switched off and the USB power source is removed from the power outlet and the product.
- Put the combs on the shaving head (Fig. 14) and the trimming head (Fig. 17) to prevent damage.
- Make sure the product and accessories are dry, then store them in the pouch if supplied, or in another safe, dry place. Keep the pouch where it will not be crushed or banged.
Do not wrap the USB cable around the product. Do not store the product where it can fall or be pulled into a tub, sink or other liquid.
Replacing the Cutting Unit
Philips advises replacing the cutting unit every 12 months, or sooner if it no longer gives the results you expect. Its lifetime varies with use. The foil becomes blunt over time, which can reduce performance and increase a hair-pulling sensation. If the foil is damaged, stop using the shaving head and replace the cutting unit immediately. Always use one of the original type.
Safety Precautions
Electrical and Water Safety
- Use only a certified USB power source rated 5 V, ≥ 1 A. In a moist environment, use only an IPX4 (splash-proof) power source. If you need help finding one, call 1-888-744-5477.
- Keep the USB cable and power source dry and away from heated surfaces.
- Plug the USB power source directly into the outlet. Do not use an extension cord.
- Connect the USB cable to the power source and the product first, then plug the power source into the outlet. Unplug the power source before connecting or disconnecting the product.
- The product does not work while connected to the power outlet.
- Never operate it with a damaged USB power source, after a drop, if it is not working properly, or after the product or power source has fallen into water.
- Do not use it outdoors, where aerosol products are in use, or where oxygen is being administered.
Skin and Personal Use
- Use only for the household use described in the manual, and only original Philips accessories or consumables.
- For hygiene, only one person should use the product.
- Do not use it on damaged, inflamed, irritated or healing skin, varicose veins, spots or moles with hairs, or skin affected by skin disease.
- Some irritation is normal during initial use and decreases as skin adjusts.
- Keep the operating product away from scalp hair, eyebrows, eyelashes and clothes.
- It is not intended for people with reduced physical, sensory or mental capabilities, or lack of experience, unless supervised or instructed by a person responsible for their safety. Supervise children.
Battery Safety
- Do not disassemble, heat above 100 °C (212 °F), incinerate, open, pierce, modify or damage the product or battery. Do not short-circuit, overcharge or reverse charge batteries.
- Keep the product away from fire, direct sunlight and high temperatures, and do not place it in a microwave oven or on an induction cooker.
- If it becomes abnormally hot or smelly, changes color, or charges longer than usual, stop using and charging it and contact Philips.
- If a battery is damaged or leaking, avoid skin and eye contact. If contact occurs, rinse immediately with water and seek medical care.
Warranty, Support and Disposal
Philips provides a full two-year warranty against defects in materials or workmanship, measured from the date of purchase and requiring a valid proof of purchase. Normal wear parts, accessories, replacement batteries and consumables such as blades and foils are not covered. A 45-day money-back guarantee also applies under the conditions in the manual. To claim either, go to www.philips.com/support or www.PhilipsMoneyBack.com respectively.
For assistance, visit www.philips.com/support or call toll free 1-888-744-5477. You can register the product at www.philips.com/welcome.
The product contains a rechargeable lithium-ion battery that must be disposed of properly. Contact your local town or city officials. In the US, call 1-800-822-8837 or visit www.call2recycle.org. In Canada, call 1-888-224-9764 or visit www.call2recycle.ca.
Frequently Asked Questions
How long does the Philips Lady Shaver BRL159 take to charge?
It takes 60 minutes to charge, and that gives up to 100 minutes of cordless use. The same applies to the BRL129, BRL147 and BRL149. The BRL127, BRL128, BRL137 and BRL138 need 8 hours of charging for up to 80 minutes of use. The BRL114 has no charging time listed. Charge before first use and whenever the indicator shows the battery is almost empty.
What do the battery indicator lights mean?
A flashing orange light means the battery is almost empty. A flashing white light means it is charging, and a solid white light means it is fully charged. About 60 seconds after a full charge, the indicator switches off by itself, so a dark indicator does not mean charging failed.
Can I use the shaver while it is plugged in?
No. The product does not work while it is connected to the power outlet, and because it is waterproof it can only be used without the cord. Charge it first, unplug it, and then use it.
What power source should I use to charge it?
Use a certified USB power source rated 5 V, ≥ 1 A, and keep it and the cable dry. For charging in a moist place such as a bathroom, use only an IPX4 (splash-proof) source. The Philips HQ87 is an example, available via www.philips.com/support. For help choosing one, call 1-888-744-5477.
Can I use it in the shower or on wet skin?
Yes. The product is waterproof, suitable for the bath or shower, and can be rinsed under the tap. Use it on completely wet skin or completely dry skin, not moist skin. Rinse the shaving head regularly during wet use. Dry use is the most efficient, and performance may be better on dry skin.
How do I switch the shaver on, change speed and control the light?
On the BRL129, BRL147, BRL149 and BRL159, press the on/off button once to switch on, and the integrated light comes on automatically. Press again for low speed, and once more to switch off. With the product switched off, hold the button for 2 seconds to turn the light off or back on. On the BRL114, BRL127, BRL128, BRL137 and BRL138, one press switches the product on or off.
Where on my body can I use each head, and what are the limits?
The shaving head is for the legs, arms, underarms and bikini area, never the face. The bikini trimming head is for hard-to-reach bikini-area spots and styling. Never use any part on the inner labia. On the outer labia, use a comb on the head. Do not use it on damaged, inflamed, irritated or healing skin, varicose veins, spots or moles with hairs, or skin affected by skin disease.
How short will the combs trim hair?
Both the shaving comb and the bikini trimming comb trim hair to 0.12 inch/3 mm. Fit the comb before you start. For the best result, move the product slowly against the direction of hair growth with the cutting unit or comb in full contact with the skin.
How do I remove and attach the combs without damaging them?
For the shaving comb, slide a fingernail between the comb and head beside the notch on the back and lift the back of the comb. Do not pull the sides or teeth. For the bikini trimming comb, put a fingernail between the comb and head on one side and pull until it comes off. Do not pull the back or teeth. To attach either one, line up the notch or indent and press until it clicks.
How do I clean the shaver properly?
Switch it off, disconnect the USB cable and remove the cutting unit. Rinse the cutting unit under the tap without using the brush on it. Use the brush on the hair chamber and all other parts, rinse them, shake off excess water and let everything air dry completely. Then click the cutting unit back in. Use only cold or lukewarm water, and never dry a cutting unit with a towel or tissue.
How often should I replace the cutting unit or oil the foils?
Philips advises replacing the cutting unit every 12 months or sooner if results drop off. Replace it at once if the foil is damaged. A drop of sewing machine oil on the trimmer teeth and foils every six weeks helps keep performance up. Order original replacement parts from the Philips website or call 1-888-744-5477.
What should I do if the shaver gets hot, smells or charges longer than usual?
Stop using and charging it right away and contact Philips at 1-888-744-5477 or www.philips.com/support. Abnormal heat, smell, color change or unusually long charging can point to a battery problem. Do not open or dismantle the product. If a battery is damaged or leaking, avoid contact with skin or eyes and rinse with water immediately if contact occurs.
