The Philips 27E1N1800A is a 27-inch monitor from the 1000 Series. It uses an IPS panel with a W-LED backlight and a native resolution of 3840 x 2160 at 60 Hz. You get two HDMI 2.0 inputs, one DisplayPort 1.4 input, an audio output, and built-in 2 W x 2 speakers. Picture presets include SmartImage and HDR modes. The stand tilts, and the monitor also accepts a 100 x 100 mm VESA mount. This manual covers only the 27E1N1800A.
Product Specifications
| Feature | Detail |
| Panel | 27″ IPS, W-LED backlight, 16:9 |
| Resolution | 3840 x 2160 @ 60 Hz (native and maximum) |
| Contrast ratio | 1000:1 (typ.) |
| Viewing angle | 178° (H) / 178° (V) |
| Colors | 1.07B (8-bit + Hi-FRC) |
| Pixel pitch | 0.1554 x 0.1554 mm |
| Refresh / frequency | 40–60 Hz vertical, 30–140 kHz horizontal |
| Inputs | 2 x HDMI 2.0, 1 x DisplayPort 1.4 (HDCP 1.4/2.2), 1 x audio out |
| Speakers | 2 W x 2 |
| Tilt | -5° to +20° |
| Size with stand (W x H x D) | 613 x 465 x 211 mm |
| Weight with stand | 4.35 kg |
| Power supply | Built-in, 100–240 VAC, 50/60 Hz |
| Power use | 27.24 W typical at 115 VAC, 52.51 W maximum, 0.5 W sleep, 0.3 W off |
| Operating environment | 0–40°C, 20–80% humidity |
Flicker-free operation, sRGB, SmartUniformity, LowBlue Mode, EasyRead, and HDR are all listed as supported.
What’s in the Box
The package includes the monitor, a base column and base stand, a Quick Start guide, and a power cable. HDMI and DisplayPort cables are packed depending on your region. SmartUniformity and Delta E information sheets are also in the box.
Ports and Controls
On the back you’ll find the Kensington anti-theft lock slot, AC power input, two HDMI 2.0 inputs, the DisplayPort input, and the audio out jack.
Everything is controlled with a single toggle button on the rear. It works like a joystick: move it in four directions to navigate and press it to select. Press it once to turn the monitor on, or hold it for more than 3 seconds to turn it off. Toggling left opens SmartImage.
Installation and Setup
Attach the base
- Lay the monitor face down on a soft, smooth surface so the screen isn’t scratched.
- Slide the base column onto the monitor until it clicks.
- Hold the base stand with both hands and push it firmly into the base column.
Connect to a computer
- Plug the power cord firmly into the back of the monitor.
- Turn off your computer and unplug its power cable.
- Connect the signal cable to the video output on your computer.
- Plug in both the computer and monitor power cords.
- Turn on the computer and the monitor. If an image appears, setup is complete.
Your graphics card must support DisplayPort 1.4 or HDMI 2.0. For 4K at 60 Hz with 10-bit color, use DisplayPort. Over HDMI 2.0, 4K at 60 Hz works in 8-bit with 4:4:4/RGB. At 30 Hz, both HDMI and DisplayPort accept 8-bit and 10-bit signals (page 16).
Wall or arm mounting
To remove the stand, place the monitor face down on a smooth surface and press the release button to detach the base column. The mounting pattern is 100 x 100 mm with M4 screws. The manual says to contact the manufacturer for wall-mount installation.
Using the On-Screen Display
The OSD menu lets you adjust the picture and settings without any software. Its main menus are:
- LowBlue Mode: On or Off, with levels 1–4.
- Input: HDMI 1, HDMI 2, DisplayPort, or Auto.
- Picture: SmartImage, SmartImage HDR, Picture Format (Wide Screen or 4:3), Brightness, Contrast, Sharpness, SmartResponse (Off, Fast, Faster, Fastest), SmartContrast, Gamma (1.8 to 2.6), Pixel Orbiting, and Over Scan.
- Audio: Volume (0–100) and Mute.
- Color: Color Temperature (Native, 5000K, 6500K, 7500K, 8200K, 9300K, 11500K), sRGB, and User Define for red, green, and blue.
- Language: 21 languages, including English, Spanish, French, and German.
- OSD Setting: Horizontal and vertical position, transparency, and timeout (5 to 60 seconds).
- Setup: Resolution Notification, Reset, and Information.
If you get lost in the menus, open Setup and choose Reset to return to factory settings. Resolution Notification shows a prompt recommending 3840 x 2160 whenever the monitor starts at a different resolution. You can turn it off in Setup.
Picture Modes and HDR
SmartImage adjusts brightness, contrast, color, and sharpness for the type of content on screen. The modes are:
- EasyRead: raises text contrast and sharpness for reading.
- Office: improves text readability and reduces eye strain.
- Photo: boosts color saturation and sharpness for images.
- Movie: more luminance, deeper color, and better detail in dark areas.
- Game: turns on overdrive for faster response.
- Economy: lowers power consumption.
- LowBlue Mode: reduces shortwave blue light.
- SmartUniformity: evens out brightness and color across the screen.
- Off: no optimization.
When the monitor receives an HDR signal, SmartImage switches to HDR Vivid, HDR Movie, Personal, or Off. SmartContrast separately analyzes the image in real time and adjusts the backlight to improve contrast.
To enable HDR in Windows 11 or 10, right-click the desktop, open Display settings, select the monitor, choose the HDR-capable display, open the Windows HD Color settings, and adjust brightness for SDR content. To turn HDR off, disable it on the source device. Mismatched HDR settings between the device and monitor can produce poor images.
Safety Instructions
- Use only the approved Philips power cord and the specified power supply. The wrong voltage can cause malfunction, fire, or electric shock.
- Keep the plug and outlet easy to reach. If you disconnect power, wait 6 seconds before reconnecting.
- Don’t block the ventilation holes, and keep objects from falling into them.
- Keep the monitor out of direct sunlight, strong light, and heat sources.
- Protect the power and signal cables from pulling, bending, and heavy objects.
- Never tilt the monitor downward more than -5°. Damage from exceeding this isn’t covered by warranty (page 1).
- Lift the monitor by the frame, never by pressing on the LCD panel.
- Only qualified service personnel should open the casing.
- Use the monitor between 0°C and 40°C and 20% to 80% humidity.
- Turn the power off and unplug immediately if water or a foreign object gets inside, then send it for service.
Static images left on screen for long periods can cause burn-in or ghost images. Use a moving screen saver when you step away, and a periodic screen refresh if the display shows unchanging content. Severe burn-in can be permanent and isn’t covered by warranty (page 3).
Cleaning and Maintenance
Unplug the monitor before cleaning. Wipe the screen with a dry cloth while it’s off, or use a slightly damp cloth for dirt. Avoid organic solvents, alcohol, and ammonia-based liquids. Oil-based cleaners can damage the plastic and void the warranty. If the monitor gets wet, dry it with a cloth as soon as possible. Unplug it if you won’t use it for a long time. Store it away from heat, direct sunlight, and extreme cold.
Troubleshooting
No picture, power LED off: Check that the power cord is seated at the outlet and the monitor. Set the rear power button to off, then on again.
No picture, power LED white: Make sure the computer is on and the signal cable is firmly connected with no bent pins. The energy-saving mode may be active.
Blurry, indistinct, or too dark image: Adjust brightness and contrast in the OSD.
Text looks fuzzy or distorted: Set the PC to the native 3840 x 2160 resolution.
Image vibrates: Check that the signal cable is secure at the graphics card or PC.
Colored or dark dots on screen: A small number is normal for LCD panels (see the pixel policy below).
Smoke or sparks: Don’t troubleshoot. Disconnect from mains power immediately and contact Philips customer service.
Pixel Defects and Warranty
Philips says pixel or sub-pixel defects can’t be fully avoided. A monitor qualifies for repair or replacement only when defects exceed the listed tolerances. Acceptable levels are up to 2 bright sub-pixel dots (no white pixels) and up to 3 black dots, with no more than 5 total dot defects. Two defects of the same type must be more than 15 mm apart.
The warranty period depends on your region and is listed in the Warranty Statement in the Important Information manual. Extended warranty options add 1, 2, or 3 years but must be bought within 30 calendar days of the original purchase. Proof of purchase is required. The Important Information manual can be downloaded from the Philips support page.
Frequently Asked Questions
What should I do if the screen says “Cannot display this video mode”?
Set your PC to 3840 x 2160 at 60 Hz. Reconnect your previous monitor if needed, change the display resolution and refresh rate in Windows, restart the computer, then reconnect the Philips monitor.
What resolution and refresh rate work best?
Native 3840 x 2160 at 60 Hz gives the best results. Your graphics card must be able to output that resolution and refresh rate.
Can I use it with a Mac?
Yes. The monitor is plug-and-play with Windows 11/10 and Mac OS X, and works with standard PCs, Macs, and workstations. A cable adapter may be needed for some Macs.
How do I reset the monitor if I get lost in the OSD?
Open the OSD, go to Setup, and select Reset to restore the original factory settings.
How do I change the color settings?
Open the Color menu in the OSD. You can pick a color temperature (5000K looks warmer, 11500K cooler), choose sRGB for consistent color across devices, or use User Define to set red, green, and blue yourself.
How should I clean the screen?
Use a clean, soft cloth. For heavier cleaning, the FAQ allows isopropyl alcohol only and rules out ethanol, acetone, and hexane. The maintenance section warns against alcohol, so a soft cloth alone is the safest choice.
Why does my display show a ghost image after I turn it off?
This is burn-in from long periods of static content. It usually fades gradually after the power is off, but severe cases may not. Use a moving screen saver or periodic screen refresh to prevent it.
Is the screen scratch resistant?
Avoid shocks, and keep the panel away from sharp or blunt objects. Don’t press on the panel surface when handling the monitor, since force on it may affect your warranty.
