Oster 14 Cup Food Processor FPSTFP4253

14 Cup Food Processor FPSTFP4253

Oster FPSTFP4253 food processor guide: parts, locking steps, pulse and speeds, chopping, slicing, shredding, cleaning, limits and warranty.
Document type
User Guide
Model number(s)
FPSTFP4253
Language
English, Spanish

Read the User Guide (PDF)

Follow the manufacturer’s safety warnings and check your exact model before using these instructions.

Oster 14 Cup Food Processor FPSTFP4253

The Oster FPSTFP4253 is a 14-cup food processor with a second, 5-cup small work bowl that nests inside the large bowl for smaller jobs. A single control knob gives you a hold-to-run PULSE position, three continuous speeds (1, 2 and 3) and OFF (O). The large bowl works with a chopping blade and a reversible slice/shred disc that fits on a disc stem. The small bowl works with a small chopping blade. A built-in interlock keeps the motor from running unless the bowl, cover and food chute lid are all locked in place.

This page covers the parts, controls, assembly, chopping, slicing and shredding procedures, food guides, cleaning and warranty terms for this model.

Parts and Controls

Parts List

Each part is labeled with a letter in the guide’s parts diagram.

LetterPart
aLarge Food Pusher
bSmall Food Pusher
cFood Chute
dSlide Release Button
eFood Chute Lid
fBowl Lid
gBowl
hCenter Post
iBase
jControl Knob
k5-Cup Small Work Bowl
lSmall Chopping Blade
mChopping Blade
nSlice/Shred Disk
oDisc Stem

Control Knob Positions

PositionWhat it does
PULSETurn the knob to the left and hold it for the unit to run. When you release it, the unit stops. Use PULSE for short jobs such as chopping nuts, raw meats or vegetables, so you can check the results and control the consistency.
1, 2, 3 (Speeds)Turn the knob to the right to 1, 2 or 3 and the unit runs continuously until you turn the knob to OFF (O).
OFF (O)Leave the processor in the OFF (O) position whenever it is not in use.

For slicing or shredding, use high speed. When using the chopping blade, use a lower speed to control the size of the chopped food.

Safety Instructions to Follow

Basic safety precautions should always be followed with electrical appliances. The safeguards listed for this unit include the following:

  1. Read all instructions before use.
  2. Do not put the food processor in water or any other liquid. This protects against electric shock and may otherwise cause personal injury or damage to the product.
  3. Close supervision is necessary when the appliance is used near children.
  4. Switch Off (O) and unplug from the outlet before putting on or taking off parts, before cleaning and when not in use.
  5. Do not contact moving parts.
  6. Do not operate the food processor with a damaged cord or plug, or after it malfunctions, is dropped or is damaged in any manner. Return it to the nearest authorized service center for examination, repair or mechanical adjustment.
  7. Attachments not recommended or sold by the manufacturer may cause fire, electrical shock or injury.
  8. Do not let the cord touch hot surfaces or hang over table edges or counters.
  9. Do not use the food processor if any part is broken.
  10. Do not use it outdoors or for commercial purposes. The unit is intended for household use only.
  11. Keep hands and utensils away from moving blades or discs while processing. A scraper may be used, but only when the food processor is not running.
  12. The blade and processing disk are sharp. Handle them carefully.
  13. Never place the cutting blade on the motor base without first putting the container properly in place.
  14. Be certain the container cover is securely locked in place while operating.
  15. Never feed food into the food chute by hand. Always use the food pusher.
  16. Turn the switch to the OFF (O) position after each use.
  17. Do not use the appliance for anything other than its intended use.
  18. Do not attempt to defeat the cover interlock mechanism.

Polarized Plug

The plug is polarized (one blade is wider than the other) and fits a polarized outlet only one way. If the plug does not insert fully, reverse it. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.

Extension Cord Use

A short power-supply cord is provided to reduce the risk of tripping over or becoming entangled in a longer cord. An extension cord may be used if care is exercised. Its electrical rating must be at least as great as the rating of the appliance, and it should be arranged so it does not drape over the countertop or tabletop where children could pull on it or someone could trip over it.

Before You Use the Food Processor

When unpacking and removing packing material, handle the chopping blade and slice/shred discs carefully because they are very sharp. Wash all parts except the base in hot, soapy water, then rinse and dry them. These parts can also go in the dishwasher; see the cleaning section for the correct method.

What This Unit Will Not Process

  • Do not try to chop ice. It will damage the bowl and dull the chopping blade.
  • The unit will not whip cream or beat egg whites.
  • It will not grind coffee beans, spices or other items with high oil content.
  • It will not slice or shred hard-cooked eggs, marshmallows or soft cheeses.

Interlock System

For your protection, the processor will not operate unless the bowl is properly locked onto the base and the cover is properly locked onto the bowl. Do not run the unit without the bowl lid, bowl and food chute lid correctly in place, and make sure the base sits on a flat, dry, clean surface before you begin. Always make sure the electric cord is unplugged while you assemble the unit.

Operating Limits

ItemLimit
Continuous running timeDo not run the processor continuously for more than 3 minutes at a time
Hot liquids and foodsLess than 176°F
Liquids per batch2 cups or less at a time (larger amounts may leak from the bowl)
PULSE hold time (chopping)About 2–3 seconds at a time

Assembling and Locking the Unit

How to Assemble the Large Bowl

  1. Align the base and bowl.
  2. Align the bowl handle with the UNLOCK mark on the base.
  3. Turn the bowl counter-clockwise until it clicks onto the base.
  4. Check that the bowl handle now aligns with the LOCK mark on the base. The handle sits above the control buttons.

There is only one position in which the bowl locks onto the base, and the unit will not operate if the bowl is not locked.

How to Lock the Cover

  1. Place the cover onto the bowl.
  2. Align the UNLOCK mark on the cover with the UNLOCK mark on the bowl.
  3. Twist the cover counter-clockwise toward LOCK until it clicks onto the bowl.
  4. Confirm the LOCK mark on the cover aligns with the LOCK mark on the bowl.

When the cover is locked, the safety mechanism on the cover and bowl aligns. The unit will not operate if the cover is not locked onto the bowl, and the bowl must be locked into the base before the cover can be locked.

How to Lock the Food Chute Lid

  1. The food chute lid hinges onto the back of the food chute.
  2. Push the Large Food Pusher down into the food chute.
  3. Push down on the tab of the Large Food Pusher to latch the food chute lid onto the food chute.

The unit will not operate if the food chute lid does not latch onto the food chute.

How to Open the Food Chute Lid

Before opening the food chute lid, turn the unit OFF (O) and unplug the cord.

  1. Pull the Slide Release Button out.
  2. Pull up the Large Food Pusher.
  3. Pull back the food chute lid and Large Food Pusher.

Chopping

How to Chop Using the Large Work Bowl

Make sure the unit is OFF (O) and unplugged before you begin. Never push food in with your hand, and do not run the processor continuously for more than 3 minutes at a time.

  1. Lock the large bowl onto the base.
  2. Grasp the chopping blade by its stem and slide it onto the center post.
  3. Place food into the bowl.
  4. Lock the cover onto the bowl.
  5. Lock the food chute lid.
  6. Plug the cord into an electric outlet. Use the Food Guide to prepare food for chopping.
  7. Turn the knob to the desired speed position for continuous processing, or to PULSE for short processing tasks. With PULSE, hold the knob in position for about 2–3 seconds at a time, check the results and repeat if desired.
  8. When finished, release the knob. If you used continuous position 1, 2 or 3, turn the knob to OFF (O) and let the chopping blade stop rotating.
  9. Twist the cover toward the UNLOCK mark to remove it.
  10. Hold the chopping blade by its stem and remove it. Unlock the bowl by turning it clockwise toward the UNLOCK mark, lift it off and empty the processed food.

The chopping blade is very sharp, so use caution when handling it.

How to Chop Using the Small Work Bowl

Do not use the slice/shred disc with the small work bowl. The same preparation rules apply: unit OFF (O) and unplugged, no hand-feeding, and no more than 3 minutes of continuous running.

  1. Lock the large bowl onto the base.
  2. Insert the small work bowl into the large work bowl and twist the inner bowl until it is seated in the large bowl.
  3. Grasp the small chopping blade by its stem and slide it onto the center post.
  4. Place food into the bowl.
  5. Lock the cover onto the bowl.
  6. Lock the food chute lid.
  7. Plug the cord into an electric outlet.
  8. Turn the knob to the desired speed for continuous processing, or to PULSE for short tasks. With PULSE, hold the knob for about 2–3 seconds at a time, check results and repeat if desired.
  9. When finished, release the knob, or if you used a continuous speed, turn the knob to OFF (O) and let the chopping blade stop rotating.
  10. Twist the lid toward the UNLOCK mark to remove it.
  11. Hold the chopping blade by its stem and remove it. Lift the small work bowl out of the larger work bowl and empty the processed food.

When using the chopping blade, use slower speeds to control the size of the chopped food.

Chopping Guide for the Large Work Bowl

FoodAmountDirections
Baby foodUp to 4 cups (1000 ml)Add up to 4 cups (1000 ml) cooked vegetables and/or meat to the bowl with ¼ cup (60 ml) liquid per cup of solid food. Process continuously to desired fineness.
Bread crumbsUp to 5 slicesCut fresh or dry bread into 1½–2 inch (3.75–5 cm) pieces. Add to bowl and process to fine crumbs.
Cookie/cracker crumbsUp to 5 cups (1250 ml)For graham crackers, chocolate or vanilla wafers. Break larger crackers into 1½–2 inch (3.75–5 cm) pieces. Add to bowl and process until fine.
Cranberries, minced3 cups (750 ml)Pulse to chop to desired fineness. Sugar can be added to make cranberry relish.
Eggs, choppedUp to 12Peel, dry and halve hard-cooked eggs. Add to bowl and pulse to chop, checking fineness after 4–5 pulses.
Garlic, mincedUp to 12Be sure the bowl is dry. Drop clove(s) down the food chute while the unit is running.
Meat, chopped (raw or cooked)Up to 2.5 cups (600 ml)Cut the meat into 1 inch (2.54 cm) cubes. Add to bowl and pulse to chop.
Mushrooms, choppedUp to 12 mediumHalve large ones and add to bowl. Pulse to desired fineness.
Nuts, chopped2 cups (300 ml)Add to bowl and pulse to chop.
Onions, choppedUp to 2 largeQuarter and add to bowl. Pulse 1 or 2 times to coarsely chop. For green onions, up to 2 cups (500 ml) cut into 1 inch pieces.
Parmesan or Romano cheese, gratedUp to 1½ cups (375 ml)Let the cheese reach room temperature. Cut into 1 inch (2.54 cm) cubes. Add to bowl and pulse to coarse chop. Process continuously to finely grate.
Parsley, choppedUp to 2 cups (500 ml)Add to bowl and pulse to chop to desired fineness, about 10–15 seconds. Process other herbs (basil, cilantro, mint, etc.) the same way.
Pepper (green, red, yellow), choppedUp to 1 pepperCut into 1 inch (2.54 cm) pieces. Add to bowl and pulse to chop.
Soups, pureed or creamed2 cups (500 ml)Add up to 2 cups hot (less than 176°F) vegetable soup. Process to desired smoothness.
Squash (butternut), pumpkin or sweet potatoes, pureedUp to 5 cups (1250 ml) of 1 inch (2.54 cm) cubesAdd ¼ cup (60 ml) cooking liquid per cup of food. Pulse to finely chop, then process continuously to puree.
Strawberries, pureed2 cups (500 ml)Hull and halve large berries. Add to bowl and pulse to chop. Process continuously to puree.
Tomatoes, chopped4 mediumQuarter tomatoes. Add up to 4 and pulse to desired size.

Slicing and Shredding

Make sure the unit is OFF (O) and unplugged before use. Never push food in with your hand, and do not run the processor continuously for more than 3 minutes at a time. The slice/shred disc has a slicing side and a shredding side; place the side you want facing up. The blades are extremely sharp.

Processing Large Amounts of Food

  1. Lock the bowl onto the base.
  2. Slide the disc stem onto the center post of the base. With the desired side facing up (slicing or shredding), push the slice/shred disc onto the disc stem.
  3. Lock the cover onto the bowl.
  4. Fill the food chute with large food such as a chunk of cabbage, a green pepper or a whole tomato. Lock the food chute lid and use the Food Guide to prepare the food.
  5. Slide the Small Food Pusher into the Large Food Pusher and plug the cord into an electric outlet.
  6. Turn the knob to the desired speed position, then press down lightly but firmly on the food pusher.
  7. When finished, turn the knob to OFF (O) and let the disc stop rotating. Twist the bowl lid toward the UNLOCK mark to remove the cover.
  8. Carefully remove the shredding disc. Unlock the bowl by turning it clockwise toward the UNLOCK mark, lift it off and empty the processed food.

The shredding disc is very sharp, so use caution when handling it.

Processing Long and Thin Foods

  1. Lock the bowl onto the base.
  2. Slide the disc stem onto the center post of the base. With the desired side facing up, push the slice/shred disc onto the disc stem.
  3. Lock the cover onto the bowl.
  4. Lock the food chute lid. It can be locked before the cover is locked onto the bowl.
  5. Fill the Large Food Pusher with long, thin food such as potato, pepperoni, carrots or celery.
  6. Insert the Small Food Pusher into the Large Food Pusher and plug the cord into an electric outlet.
  7. Turn the knob to 1, 2 or 3, then press down lightly but firmly on the Small Food Pusher.
  8. When finished, turn the knob to OFF (O) and let the disc stop rotating. Twist the bowl lid toward the UNLOCK mark to remove the cover.
  9. Carefully remove the shredding disc. Unlock the bowl by turning it clockwise toward the UNLOCK mark, lift it off and empty the processed food.

Slicing Guide for the Large Work Bowl

FoodDirections
AppleHalve and stack horizontally in the chute. Use firm pressure.
Cabbage/lettuceHalve the head and cut to fit the chute.
CarrotsCut to fit the chute.
CeleryRemove string and pack the chute for best results.
CucumberCut to fit the chute if necessary.
MushroomsStack the chute with mushrooms on their sides for lengthwise slices.
OnionsHalve and fill the chute, positioning onions upright for coarsely chopped results.
Peaches/pearsHalve and core. Position upright in the chute and slice using light pressure.
Peppers (green, yellow, red, etc.)Halve and seed. Fit the pepper up the bottom of the chute, squeezing slightly to fit if necessary. Cut large ones into quarters or strips, depending on desired results. Slice using moderate pressure.
PepperoniCut into 3 inch (8 cm) lengths. Remove inedible casing.
PotatoesPeel if desired. Cut large potatoes in halves and position in the chute.
StrawberriesHull. Arrange berries on their sides for lengthwise slices.
TomatoesUse small tomatoes for whole slices, halved if necessary. Use gentle but firm pressure.
TurnipsPeel and cut to fit the chute.
ZucchiniSlice off ends. Use small squash for whole slices; halve larger ones to fit the chute.

Shredding Guide for the Large Work Bowl

FoodDirections
CabbageUse the shredding disc for very fine cabbage or slaw. Cut into pieces to fit the chute. Shred using light pressure. Empty the bowl as cabbage reaches the disc.
CarrotsPosition in the chute and shred.
Cheese, cheddarCheese must be well chilled. Cut to fit the chute and use light pressure.
Cheese, mozzarellaCut to fit the chute. Chill in the freezer for 30 minutes before shredding. Use light pressure.
PotatoesCut to fit the chute.
ZucchiniSlice off ends and cut to fit the chute, either lengthwise or horizontally.

Processing Liquids and Hot Foods

Hot liquids (less than 176°F) and hot foods can be processed in the bowl. Process small amounts of liquid, 2 cups or less at a time, because larger amounts may leak from the bowl.

Care and Cleaning

The cutting edges of the chopping blade and the reversible disc are permanently sharpened at the factory. Do not try to sharpen them; attempted sharpening will ruin them.

Cleaning Steps

  1. Before cleaning, make sure the unit is switched off and the cord is unplugged.
  2. Whenever possible, rinse parts right after processing for easier cleanup.
  3. Wipe the base, control knob and feet with a damp cloth and dry thoroughly. Stubborn spots can be rubbed with a damp cloth and a mild, non-abrasive cleaner. Do not immerse the base in liquid.
  4. Remember that the blades are sharp.
  5. All removable parts can be washed by hand or in a dishwasher, top rack only.
    • By hand: wash in hot sudsy water, rinse and dry thoroughly. If necessary, use a small nylon bristle brush to clean the bowl and food chute/cover. This type of brush also helps prevent cuts from the sharp chopping blade and slice/shred disc.
    • In a dishwasher: place removable parts on the top rack only, not in or near the utensil basket.
  6. Do not use rough scouring pads or cleansers on any plastic or metal parts.
  7. Do not fill the bowl with boiling water or place any parts in boiling water.

Removing and Re-Attaching the Wide Mouth Food Chute

For easier cleaning, the wide mouth food chute can be removed from the lid.

To remove it:

  1. Pull the Slide Release Button out and pull up the Large Food Pusher.
  2. Pull back the food chute lid and Large Food Pusher.
  3. Push in the white horizontal hinge pin and lift off the wide mouth food chute.

To re-attach it:

  1. Line up the white horizontal hinge pin with the notches.
  2. Push in to lock it into place.

Removing Stains from the Bowl

Some foods, such as carrots, may temporarily stain the bowl. To remove stains, make a paste of 2 tablespoons (30 ml) baking soda and 1 tablespoon (15 ml) warm water. Apply the paste to the stains and rub with a cloth. Rinse with sudsy water and dry.

Warranty and Customer Support

One-Year Limited Warranty

For one year from the date of purchase, Sunbeam Products, Inc. doing business as Jarden Consumer Solutions (or, in Canada, Sunbeam Corporation (Canada) Limited doing business as Jarden Consumer Solutions, together “JCS”) warrants that this product will be free from defects in material and workmanship. At its option, JCS will repair or replace the product or any defective component with a new or remanufactured product or component. If the product is no longer available, a similar product of equal or greater value may be used. This is the exclusive warranty.

The warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable. Keep the original sales receipt, because proof of purchase is required for warranty service. Do not try to repair or adjust any electrical or mechanical function of the product, as doing so will void the warranty.

The warranty does not cover normal wear of parts or damage from negligent use or misuse, use on improper voltage or current, use contrary to the operating instructions, disassembly, repair or alteration by anyone other than JCS or an authorized JCS service center, or acts of God such as fire, flood, hurricanes and tornadoes. Some provinces, states or jurisdictions do not allow the exclusion or limitation of certain damages or implied-warranty limits, so some limitations may not apply to you.

Contact Details

RegionPhone
USA1.800.334.0759
Canada1.800.667.8623

The website listed in the guide is www.oster.com. For warranty service, call the number for your country and a convenient service center address will be provided. Do not return the product to the company addresses given in the warranty or to the place of purchase.

Frequently Asked Questions

Why won’t my Oster FPSTFP4253 food processor start?

Check the three lock points first, because the interlock system stops the motor unless all of them are engaged. The bowl must be locked onto the base, with the bowl handle at the LOCK mark above the control buttons. The cover must be twisted counter-clockwise until it clicks and its LOCK mark lines up with the LOCK mark on the bowl, and the food chute lid must be latched onto the food chute by pushing down the tab of the Large Food Pusher. The bowl has to be locked to the base before the cover can be locked. Also confirm the cord is plugged in and the base is on a flat, dry, clean surface. If it still will not run after that, see the warranty and service contact information rather than adjusting any electrical or mechanical parts yourself.

What does the PULSE position do on the control knob?

PULSE is a hold-to-run setting. Turn the knob to the left and hold it there and the processor runs; let go and it stops. It suits short jobs such as chopping nuts, raw meats or vegetables because you can stop and check the texture. For chopping, hold the knob in PULSE for about 2–3 seconds at a time, check the results and repeat until the food reaches the size you want.

Which speed should I use for chopping, slicing and shredding?

Use a lower speed with the chopping blade so you can control the size of the chopped food, and use high speed for slicing or shredding. The knob has three continuous positions, 1, 2 and 3, and the unit keeps running in any of them until you turn the knob to OFF (O). For long, thin foods fed through the Large Food Pusher, set the knob to 1, 2 or 3 and press down lightly but firmly on the Small Food Pusher.

How long can I run the food processor at one time?

Do not run it continuously for more than 3 minutes at a time. That limit appears in every chopping, slicing and shredding procedure. When you are chopping, using PULSE in 2–3 second bursts is a good way to stay well within it while checking your results.

Can I chop ice, whip cream or grind coffee in this food processor?

No. Do not try to chop ice, because it will damage the bowl and dull the chopping blade. The unit also will not whip cream or beat egg whites, grind coffee beans, spices or other high-oil items, or slice or shred hard-cooked eggs, marshmallows or soft cheeses. Hard-cooked eggs can be chopped, though: peel, dry and halve them, add them to the bowl and pulse, checking fineness after 4–5 pulses.

How do I use the 5-cup small work bowl?

Lock the large bowl onto the base first, then set the small work bowl inside it and twist the inner bowl until it seats. Slide the small chopping blade, not the large one, onto the center post by its stem, add your food, then lock the cover and the food chute lid before plugging in. Choose a continuous speed or PULSE as you would in the large bowl. When you finish, unlock the cover, remove the blade by its stem and lift out the small bowl. Do not use the slice/shred disc with the small work bowl.

Can I process hot liquids or hot soup in the bowl?

Yes, within limits. Hot liquids and hot foods under 176°F can be processed, and you should keep liquid to 2 cups or less per batch because larger amounts may leak from the bowl. For pureeing or creaming soup, add up to 2 cups of hot vegetable soup (less than 176°F) and process to the smoothness you want. Do not fill the bowl with boiling water when cleaning it either.

How do I shred mozzarella or cheddar cheese?

Chill the cheese first and keep the pressure light. Cheddar must be well chilled and cut to fit the food chute. Mozzarella should be cut to fit the chute and chilled in the freezer for 30 minutes before shredding. Use the shredding side of the slice/shred disc, facing up on the disc stem, and avoid soft cheeses, which the unit will not slice or shred.

Is the Oster FPSTFP4253 dishwasher safe?

The removable parts are, but the base is not. Place the removable parts on the top rack only, not in or near the utensil basket. The base, control knob and feet should only be wiped with a damp cloth and dried thoroughly, and the base must never be immersed in liquid. If you wash by hand, use hot sudsy water, rinse and dry thoroughly, and consider a small nylon bristle brush to help avoid cuts from the blade and disc.

How do I take the wide mouth food chute off for cleaning?

Pull out the Slide Release Button and pull up the Large Food Pusher, then pull back the food chute lid and Large Food Pusher. Push in the white horizontal hinge pin and lift the wide mouth food chute off the lid. To put it back, line the hinge pin up with the notches and push in until it locks. Switch the unit off and unplug it before handling any parts.

How do I remove stains from the bowl?

Carrots and some other foods can temporarily stain the bowl. Mix 2 tablespoons (30 ml) of baking soda with 1 tablespoon (15 ml) of warm water to make a paste, rub it onto the stains with a cloth, then rinse with sudsy water and dry. Avoid rough scouring pads or cleansers on plastic or metal parts.

Follow the manufacturer’s safety warnings and check your exact model before using these instructions. Report an error.

Document information and editorial sourcing

The product instructions/information above in this page are based on the original manufacturer document.

Last updated: November 18, 2026

Find more product manuals in:

Related Oster Manuals