The Philips Curved Business Monitor 49B2U5900CH, part of the 5000 Series, is a 48.8-inch (124 cm) curved VA display with a 32:9 aspect ratio and a native resolution of 5120 x 1440. It works as a desk hub as well as a screen. Video comes in over USB-C, DisplayPort or two HDMI 2.0 ports, and the main USB-C port can power a laptop at a typical 96 W. The monitor also adds a USB hub, gigabit Ethernet, a pop-up 5.0-megapixel Windows Hello webcam, two 3 W speakers and a KVM switch for running two PCs from one keyboard and mouse.
Product Specifications
| Item | Detail |
| Panel | 48.8″ VA, W-LED backlight, 3000:1 typical contrast, 178°/178° viewing angle |
| Resolution | Native 5120 x 1440 @ 60 Hz; maximum 5120 x 1440 @ 75 Hz |
| Colors and HDR | 1.07 billion colors (8 bits + FRC); VESA DisplayHDR 400 |
| Video inputs | 2 x HDMI 2.0, 1 x DisplayPort 1.4, 1 x USB-C (DP Alt mode) |
| USB | USB-C1 upstream (PD 3.0, typical 96 W), USB-C2 downstream (up to 15 W), USB-B upstream, 2 x USB-A downstream (one fast-charge port, up to 7.5 W) |
| Network and audio | RJ45 Ethernet (1000M on USB 3.2); combo audio out/microphone in jack |
| Stand | Tilt -5° to +15°, swivel ±30°, height adjustment 150 mm |
| Mounting | VESA 100 x 100 mm, M4 screws |
| Size with stand | 1193 x 583 x 268 mm (W x H x D), 15.21 kg |
| Power | Built-in supply, 100–240 V AC; 45.1 W typical at 115 V AC; 0.3 W in sleep |
| Operating range | 0°C to 40°C, 20% to 80% humidity |
(PDF p. 33–35)
Installation and Setup
The box holds the monitor, a quick start guide, a power cord and a set of signal and USB cables (DP, HDMI, USB C-C/A, USB C-C, USB C-A and USB A-B). The cables supplied differ by region.
Attaching the Base
The screen is curved, so support it with protective material underneath and never press down on the panel while attaching or removing the base.
- Lay the monitor face down on a cushion.
- Hold the stand with both hands and attach the base. Tighten the screws on the underside of the base.
- Press the stand onto the VESA mount area until the latch locks.
- Stand the monitor up with the styrofoam still on, then pull the styrofoam out without squeezing the panel.
Connecting to a Computer
- Plug the power cord firmly into the back of the monitor.
- Turn off the computer and unplug its power cable.
- Connect the signal cable to the video output on the computer.
- Plug the computer and monitor into a nearby outlet.
- Turn on both. If an image appears, setup is complete.
Controls and On-Screen Menu
The bezel keys cover power, OSD access and confirmation, input source, back, a customizable user key, the SmartImage hot key, microphone mute, a call hook button and the Busylight. Menus are navigated with a single joystick-style toggle on the rear: move it in four directions and press to select (PDF p. 14).
The main menu holds PowerSensor, LightSensor, Input, Picture, PIP/PBP, Audio, Color, Language, OSD Setting, USB Setting, Webcam and Setup. Setup > Reset restores factory settings. The user key can be set to Volume, MultiView, Brightness, KVM or PowerSensor.
USB-C, USB Hub and Ethernet
The USB-C input defaults to High Data Speed. If your computer does not support HBR 3, open USB Setting and choose High Resolution, which limits output to 5120 x 1440 @ 75 Hz. If Ethernet seems slow, switch back to High Data Speed, which supports 1G LAN speed (PDF p. 16).
The Ethernet port needs the Realtek USB Ethernet driver from the Philips support page. Install the matching driver, then restart the computer (PDF p. 9).
The USB ports shut down in standby and off modes. Turn on USB Standby Mode in the OSD (default is Off) to keep charging and connected devices working in sleep. Switching the monitor off at its power switch powers down every USB port.
Webcam and Calls
The pop-up webcam sits on top of the monitor. Press it to raise it, and tilt it back up to 30 degrees. Connect a USB cable from your PC to the USB C or USB UP port, then pick the matching option in the KVM menu. Windows Hello face login uses the Windows 11 sign-in setup: Settings > Accounts > Sign-in options, create a PIN, then choose Get started. On older Windows versions and macOS the webcam works without face recognition (PDF p. 17–18).
An activity light shows when the webcam is on. Its brightness runs from 0 (off) to 4, default 1, under Webcam > Busylight. The Busylight button turns the webcam light red to signal that you are busy, and it comes on automatically during Teams or Skype calls. The hook button accepts or ends calls in those apps and works only with a USB upstream cable connected.
KVM and MultiView
Running Two PCs
Connect each PC with the right pair of cables. An HDMI or DP source pairs with the USB UP port. A source on USB C1 pairs with a USB-C cable to USB C1. Then open the KVM menu and choose Auto, USB C or USB UP. With Auto, pressing Ctrl three times switches sources. Input selection is not automatic, so select the input in the OSD (PDF p. 20–21).
PIP and PBP
MultiView shows two sources at once. Under PIP/PBP, choose PIP (a sub-window) or PBP (side by side), then set the input, PIP size (Small, Middle, Large), PIP position and Swap. Any input can serve as main or sub source. The black strips above and below the picture in PBP mode are normal. Audio follows the main source, and Swap switches video and audio together (PDF p. 22–23).
Picture Settings
SmartImage modes are EasyRead, Office, Photo, Movie, Game, Economy, SmartUniformity and Off. With an HDR signal, the same key opens HDR Premium, HDR Movie, HDR Photo, DisplayHDR 400, HDR Basic or Off. PowerSensor detects whether you are seated 30 to 100 cm (12 to 40 inches) away and cuts power use when you leave. It works in landscape orientation only.
Safety and Maintenance
- Do not tilt the screen down more than -5°. Beyond that, damage is not covered by warranty (PDF p. 3–4).
- Lift the monitor by the frame, never by the panel.
- Keep vents clear and the monitor away from sunlight, heat and moisture.
- Use only the supplied Philips power cord. After unplugging, wait 6 seconds before reconnecting.
- Connect only equipment with a fire enclosure complying with IEC 62368-1 or IEC 60950-1 to the USB-C port.
- Run a moving screen saver or periodic refresh when static content is on screen. Severe burn-in is not covered by warranty (PDF p. 5).
- Unplug the monitor before cleaning. Wipe with a dry or slightly damp cloth. Do not use oil-based cleaners.
- Only qualified service personnel should open the casing.
Troubleshooting
| Problem | What to try |
| No picture, power LED off | Check the power cord at the outlet and monitor. Set the power switch off, then on. |
| No picture, LED white | Confirm the computer is on, the signal cable is seated and has no bent pins. Energy saving may be active. |
| Blurred, dark or distorted image | Adjust brightness and contrast. Set the PC to the native resolution, 5120 x 1440. |
| Colored or dark dots | Normal for LCD panels; see the pixel policy. |
| Power light too bright | Lower the Power LED setting in the Setup menu. |
| Smoke or sparks | Disconnect from mains power immediately and contact Philips customer service. |
Under the pixel policy, repair or replacement requires more than 5 total dot defects, more than 2 bright dots or more than 3 black dots, among other limits (PDF p. 41).
Frequently Asked Questions
What resolution and refresh rate should I use?
Use 5120 x 1440 at 60 Hz. If you see screen disturbance, you can try 75 Hz. If the screen says it cannot display the video mode, set the resolution from a PC that already works with the previous display, then reconnect the monitor (PDF p. 44).
Why don’t my USB ports charge when the monitor sleeps?
USB Standby Mode is off by default. Turn it on in USB Setting to keep USB power and charging active in standby. It must be set again after a factory reset.
Can I use Windows Hello on Windows 10?
The setup instructions call for Windows 11, but the compatibility table also lists Windows 10 as supporting face recognition. Windows 8 and 8.1 get the webcam only. If the webcam or Face Recognition option is greyed out, open Task Manager > Services, stop and restart Windows Biometric Service (WbioSrvc), then redo the sign-in setup (PDF p. 46–47).
How do I wall-mount the monitor?
The monitor accepts a 100 x 100 mm VESA mount with M4 screws. With the monitor face down, press the release button to detach the neck. Contact the manufacturer for wall-mount installation (PDF p. 24).
Can I clean the screen with alcohol?
For normal cleaning, use a clean, soft cloth. One FAQ allows isopropyl alcohol for extensive cleaning, but the safety section warns against alcohol and ammonia-based liquids. A dry or slightly damp cloth is the safer choice.
Why does the PIP or PBP sub-window flicker?
The sub-window source is probably using interlaced timing. Change it to progressive timing (PDF p. 47).
