Philips Norelco All-in-One Trimmer MG3919

All-in-One Trimmer MG3919

Set up, charge, attach guards, trim and clean the Philips Norelco MG3919 and MG3939 All-in-One Trimmer with step-by-step instructions.
Document type
User Manual
Model number(s)
MG3919, MG3939
Language
English, Spanish

Read the User Manual (PDF)

Follow the manufacturer’s safety warnings and check your exact model before using these instructions.

Philips Norelco All-in-One Trimmer MG3919

The Philips Norelco MG3919 is a cordless, rechargeable trimmer for the beard, head and face. A single handle takes a cutting element, interchangeable stubble, beard and hair guards, and a nose and ear hair trimmer head. Used without a guard, the cutting element trims close to the skin (about 1/32 in. or 0.5 mm) and creates clean lines around the beard, neck and sideburns. Fully charged, it runs cordless for up to 60 minutes. It cannot run while plugged in. This page also covers the MG3939, which shares the same handle and adds a precision trimmer for fine lines and contours.

Parts and Controls

Trimmer Parts

No.PartNotes
1Nose and ear hair trimmer
2Cutting elementMG3919
3Precision trimmerMG3939
4Cutting elementMG3939
5On/off buttonPress once to switch on or off
6Battery status indicatorLights up continuously while connected to the power outlet
7Socket for small plugIn the bottom of the product
8USB cable

The USB power source is not included. Philips lists the HQ87 as a suitable example, available through www.philips.com/support. The cleaning brush and storage pouch are supplied but not shown in the parts figure.

Guards

The number on each guard is the hair length, in millimeters, that remains after trimming.

No.GuardLength
9Stubble guard1 mm (3/64 in.)
10Beard guard3 mm (1/8 in.)
11Beard guard5 mm (3/16 in.)
12Beard guard7 mm (9/32 in.)
13Stubble guard (MG3919)2 mm
14Hair guard9 mm (3/8 in.)
15Hair guard12 mm (15/32 in.)
16Hair guard16 mm (21/32 in.)

Specifications and Model Differences

ItemMG3919MG3939
Full charge time10 hours8 hours
Cordless operating time (fully charged)Up to 60 minutesUp to 60 minutes
Cutting elementItem 2Item 4
Precision trimmerNot listedItem 3 (MG3939 only)
2 mm stubble guardItem 13 (listed for MG3919)Not listed
Nose and ear hair trimmerIncluded (item 1)Included (item 1)

Both models share these values:

  • USB power source: certified, output rating 5 V, ≥ 1 A
  • Battery: rechargeable NiMH
  • Charging and use temperature: between 41 °F / 5 °C and 95 °F / 35 °C
  • Use: household use only, without the cord
  • Model number location: on the back of the product. The full model number (for example MG1234/56) is on the bottom of the packaging, your receipt or your order confirmation.

Safety Information

Read all instructions before using the trimmer. Basic electrical precautions apply to any electric product.

Electrical and Water Safety

  • Charge only with a USB power source on a certified product with an output rating of 5 V, ≥ 1 A. A non-certified USB power source may cause hazards or serious injuries. For help finding the right one, call Philips support at 1-800-243-3050.
  • Keep the product, the USB cable and the USB power source dry. Use the product only when it is dry. Do not use it while bathing or in a shower.
  • Do not place or store the product where it can fall or be pulled into a tub or sink. Do not place or drop it into water or other liquid.
  • The product does not work while connected to the power outlet. Except when charging, always unplug it from the power outlet.
  • Always attach the USB cable to the USB power source and the product first, then attach the USB power source to the power outlet. To disconnect, set all controls to the off position, then remove the USB power source from the power outlet.
  • Plug the USB power source directly into a power outlet. Do not use an extension cord.
  • Do not use the USB power source in or near an outlet that contains an electric air freshener.
  • Keep the USB cable and USB power source away from heated surfaces.
  • Remove the USB power source from the power outlet and the product before cleaning.

Battery and Temperature Safety

  • Charge, use and store the product between 41 °F / 5 °C and 95 °F / 35 °C. Charging or using it outside this range adversely affects battery lifespan.
  • Keep the product and its batteries away from fire. Do not expose them to direct sunlight or high temperatures.
  • Do not place the product or its batteries in a microwave oven or on an induction cooker.
  • Stop using and charging the product, and contact Philips, if it becomes abnormally hot or smelly, changes color, or takes longer than usual to charge.
  • Do not open, modify, pierce, damage or dismantle the product or battery. Do not short-circuit, overcharge or reverse charge batteries.
  • If batteries are damaged or leaking, avoid contact with skin or eyes. If contact occurs, rinse well with water immediately and seek medical care.
  • After removal, keep battery terminals away from metal objects such as coins, hairpins and rings. Do not wrap batteries in aluminum foil. Tape the terminals or put the batteries in a plastic bag before discarding them.

General Use Safety

  • This product is not intended for people (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless a person responsible for their safety supervises or instructs them. Supervise children so they do not play with the product.
  • Use the product only for its intended household use. Misuse can lead to hazards or serious injuries. Do not use attachments that Philips North America LLC does not recommend, and use only original Philips accessories or consumables.
  • Never operate the product if the USB power source is damaged, if the product is not working properly, after it has been dropped or damaged, or after it or the USB power source has fallen into water. For assistance, call 1-800-243-3050.
  • Always check cutting units, attachments and accessories before use. Never use the product with a damaged one, as injury may occur. Replace a damaged part with one of the original type.
  • Do not use the product outdoors, where aerosol (spray) products are being used, or where oxygen is being administered.
  • Never drop or insert any object into any opening.
  • Because of hygiene, only one person should use the product.
  • The product has no other user-serviceable parts.

Charging the Trimmer

Charge the trimmer before first use and again when the motor starts working more slowly. If the trimmer has just gone through a major change in temperature, pressure or humidity, let it acclimatize for 30 minutes before use.

A full charge takes 10 hours (MG3919) or 8 hours (MG3939) and gives up to 60 minutes of cordless operation.

Warning: Keep the USB cable and the USB power source dry.

  1. Make sure the trimmer is switched off.
  2. Insert the small plug of the USB cable into the socket in the bottom of the trimmer.
  3. Insert the USB plug into the USB power source (not included).
  4. Insert the USB power source into the power outlet.
  5. When charging is complete, pull the small plug out of the trimmer and remove the USB power source from the power outlet.

The battery charge indicator lights up continuously while the trimmer is connected to the power outlet.

Attaching and Detaching Parts

Switch the trimmer off before attaching or removing any attachment and before cleaning.

Cutting Element

  1. To detach, place your thumb below the teeth of the cutting element and gently push upward until it comes off the handle.
  2. To attach, insert the plastic notch at the back of the cutting element into the guiding slot in the handle. Then gently press the teeth downward until the cutting element clicks into place.

Nose and Ear Hair Trimmer

To detach it, place your finger on the recess at the back of the attachment and push the attachment off the handle. Use your other hand to keep it from dropping on the floor.

Guards

  1. To attach any guard, slide the front part of the guard onto the teeth and press the plastic notch at the back of the guard downward until it clicks into place.
  2. To detach any guard, carefully push its back part off the product, then slide it off the cutting element.

Switching On and Off

Press the on/off button once to switch the trimmer on or off.

Trimming Tips

  • The first time you trim, start with the guard that has the maximum trimming length setting to get familiar with the trimmer.
  • Hairs grow in different directions, so try trimming upward, downward and across. Practice gives the best results.
  • Make smooth, gentle movements and keep the surface of the guard in contact with your skin.
  • Use the trimmer on clean, dry hair. Wet hair tends to stick to the body.
  • If too much hair builds up on the trimmer, remove it before or during use for better results (see Cleaning).

Trimming Your Beard

Comb your beard or mustache with a fine comb before you start.

Trimming Without a Guard

Used without a guard, the cutting element trims hair close to the skin (about 1/32 in. or 0.5 mm) and creates clean lines around the beard, neck and sideburns.

  1. For a close trim, place the flat side of the cutting element against your skin and make strokes against the direction of hair growth.
  2. For contouring, hold the cutting element perpendicular to the skin and move it upward or downward with gentle pressure.
  3. Switch off and clean the trimmer after each use.

Trimming With a Stubble or Beard Guard

  1. Attach a stubble or beard guard to the cutting element.
  2. Move the guard against the direction of hair growth for the most effective trim. Keep the surface of the guard in contact with the skin.
  3. Switch off and clean the trimmer after each use.

Trimming Hair on Your Head

Comb your hair first, and use the trimmer on clean, dry hair.

  1. Attach a hair guard to the cutting element.
  2. Move the trimmer slowly over the crown from different directions for an even result. Always move against the direction of hair growth, press lightly, and keep the guard in contact with the skin.
  3. Make overlapping passes over the head so all hair that should be cut has been cut.
  4. Gently shake hairs off the trimmer between strokes so they do not collect between the cutting element and the guard.
  5. Switch off and clean the trimmer after each use.

Precision Trimmer (MG3939 Only)

The precision trimmer creates fine lines and contours around your facial style, close to the skin, to a length of 1/32 in. (0.5 mm).

  1. Hold the precision trimming head perpendicular to the skin and move it upward or downward with gentle pressure.
  2. Switch off and clean the trimmer after each use.

Nose and Ear Hair Trimmer

Use this attachment to shorten nose and ear hair.

  • Make sure nasal passages are clean and outer ear channels are clean and free from wax.
  • Do not insert the cutting element too deep into your nostrils or ear channels (max. 3/16 in. or 5 mm).
  • When trimming both nose and ear hair, make firm, rotary movements so the cutting element reaches all the hairs.
  • Clean the attachment after each use.

Note: The attachment is not designed to clean-shave your nostrils or ear channels. It shortens the hairs. Nose and ear hairs have important protective functions and should not be fully removed.

Trimming Nose Hair

  1. Make sure the trimmer is switched off, then gently insert the cutting element into one nostril.
  2. Move the tip in and out of the nostril in a firm, rotary motion to cut the hairs to a shorter length.

Trimming Ear Hair

  1. Slowly move the cutting element along the outer ear to trim hairs that stick out beyond the rim.
  2. Gently insert the cutting element into the outer ear channel. Move the tip in and out in a firm, rotary motion to cut the hairs to a shorter length.
  3. Switch off and clean the attachment after each use.

Cleaning

Never rinse the handle under the tap or immerse it in water. Only the cutting element and the attachments can be rinsed under the tap, and only when detached from the handle. Getting the handle wet may cause irreversible damage and make the product unusable.

  • Switch off the product before removing or attaching attachments and before cleaning.
  • Use only cold or lukewarm water on the cutting element and attachments.
  • Never use scouring pads, abrasive cleaning agents or aggressive liquids such as gasoline or acetone.
  • Never dry the cutting element with a towel, brush or tissue, as this may damage the teeth.

Before cleaning, make sure the trimmer is off and the USB power source is removed from both the power outlet and the product. Wipe the handle with a dry cloth.

Cleaning With the Brush

  1. Detach any guard and clean it with the cleaning brush.
  2. Detach the cutting element. Clean the teeth and the inside of the cutting element with the brush.
  3. Clean the inside of the hair chamber with the brush.

Keep the handle away from water, and make sure no water reaches the inside of the hair chamber.

Cleaning Under the Tap

  1. Detach any guard and the cutting element, and rinse them under the tap.
  2. Carefully shake off excess water and let the parts air-dry completely before reattaching them.

Cleaning the Nose and Ear Hair Trimmer

Clean it immediately after use and whenever a lot of hair or dirt has built up on the cutting element.

  1. Detach the nose and ear hair trimmer from the handle.
  2. Rinse the trimmer head under running tap water.
  3. For a thorough clean, soak the head in a bowl of warm water for a few minutes to soften debris, then rinse under running tap water to remove stubborn debris.
  4. Carefully shake off excess water and let all parts air-dry completely before reattaching them.

Storage

  • Do not place or store the trimmer where it can fall or be pulled into a tub, sink, water or other liquid.
  • Make sure it is switched off and the USB power source is removed from the power outlet and the product.
  • Do not wrap the USB cable around the product.
  • Make sure the product and accessories are dry before storing them.
  • Store the trimmer, the USB power source and all accessories in the supplied pouch. Keep the pouch in a safe, dry place where it will not be crushed, banged or damaged.

Warranty, Support and Disposal

  • Support: Visit www.philips.com/support or call toll free 1-800-243-3050. Register your product at www.norelco.com/register.
  • Warranty: Philips North America LLC provides a Full Two-Year Warranty against defects in materials or workmanship from the date of purchase and will repair or replace a defective product without charge. It does not cover damage from accident, misuse or abuse, lack of reasonable care, attachments not provided with the product, loss of parts, or use at other than the specified voltage. Cutting units and guards are not covered because they wear.
  • 45-day money-back guarantee: Go to www.PhilipsMoneyBack.com. The product must be shipped prepaid by insured mail with the original sales receipt and postmarked no later than 45 days after purchase.
  • Disposal: The product contains a rechargeable NiMH battery that must be disposed of properly. Contact local town or city officials, call 1-800-822-8837, or visit www.call2recycle.org for battery drop-off locations. For recycling information, visit www.recycle.philips.com.

Frequently Asked Questions

How long does the Norelco MG3919 or MG3939 take to charge, and how long does it run?

A full charge takes 10 hours on the MG3919 and 8 hours on the MG3939. Once fully charged, either model runs cordless for up to 60 minutes. Charge it before first use, and again whenever the motor starts working more slowly.

What kind of USB power source does this trimmer need?

Use a USB power source on a certified product with an output rating of 5 V, ≥ 1 A. A power source isn’t included, but Philips lists the HQ87 as a suitable example through www.philips.com/support. If you aren’t sure which one to buy, Philips support can help at 1-800-243-3050. A non-certified power source may cause hazards or serious injuries.

How do I charge the trimmer, and how can I tell it’s charging?

Switch the trimmer off, push the small plug of the USB cable into the socket in the bottom of the handle, plug the USB end into the power source, then put the power source into the wall outlet. The battery indicator stays lit continuously while the trimmer is connected to the power outlet. Plug the cable into the power source and trimmer first, and the power source into the outlet last. When you finish, remove the small plug and unplug the power source. Plug the power source straight into a wall outlet, not an extension cord, and keep the cable and power source dry.

Can I use the trimmer while it is plugged in?

No. The trimmer works only without the cord and does not run while connected to the power outlet. Charge it first, then unplug it before you trim.

What do the numbers on the guards mean?

Each number is the length of hair, in millimeters, that remains after trimming. The set includes stubble guards of 1 mm and 2 mm (the 2 mm is listed for the MG3919), beard guards of 3, 5 and 7 mm, and hair guards of 9, 12 and 16 mm. If this is your first time trimming, start with the guard with the longest setting to get used to the trimmer, then work down.

How do I attach and remove the cutting element and guards?

Switch the trimmer off first. To remove the cutting element, put your thumb below its teeth and push gently upward until it comes off. To put it back, fit the plastic notch on its back into the guiding slot in the handle and press the teeth down until it clicks. For a guard, slide its front part onto the teeth and press the notch at the back down until it clicks. To remove it, push the back part off, then slide the guard off the cutting element.

How do I get a close trim or clean lines around my beard, neck and sideburns?

Use the cutting element without a guard. Lay the flat side against your skin and stroke against the direction of hair growth to trim hair to about 1/32 in. (0.5 mm). For contouring, hold the cutting element perpendicular to the skin and move it up or down with gentle pressure. On the MG3939, the precision trimmer is also made for fine lines and contours to the same 1/32 in. (0.5 mm) length: hold the head perpendicular to the skin and move it up or down gently. Comb your beard first, and clean the trimmer after each use.

How deep can I insert the nose and ear hair trimmer, and will it remove all the hair?

Insert it no deeper than 3/16 in. (5 mm) into the nostril or outer ear channel. It isn’t designed to clean-shave these areas. It shortens the hairs, and nose and ear hairs have protective functions, so they shouldn’t be fully removed. Make sure nasal passages and ear channels are clean, and use firm, rotary movements so the cutting element reaches all the hairs.

Can I rinse the trimmer under the tap or use it in the shower?

Do not use the trimmer while bathing or in a shower. Never rinse the handle under the tap or immerse it in water, because getting the handle wet may cause irreversible damage and make the product unusable. Only the cutting element, guards and attachments can be rinsed under the tap, and only after you detach them from the handle. Use cold or lukewarm water.

How do I clean the cutting element and guards?

Switch off the trimmer and disconnect the USB power source. Wipe the handle with a dry cloth, then take off the guard and cutting element. You can brush them clean, including the teeth, the inside of the cutting element and the hair chamber, or rinse the detached parts under the tap. Shake off the water and let the parts air-dry completely before reattaching them. Never dry the cutting element with a towel, brush or tissue, which may damage the teeth. Don’t use scouring pads or abrasive or aggressive liquids such as gasoline or acetone.

What should I do if the trimmer slows down, gets very hot, smells or takes longer to charge?

If the motor works more slowly, charge the trimmer. If it becomes abnormally hot or smelly, changes color, or takes longer than usual to charge, stop using and charging it and contact Philips at www.philips.com/support or 1-800-243-3050. Never operate the trimmer if it has been dropped or damaged, or if it or the USB power source has fallen into water.

What does the warranty cover?

Philips North America LLC gives a two-year warranty from the date of purchase against defects in materials or workmanship and will repair or replace a defective product without charge. It excludes accident, misuse or abuse, lack of reasonable care, attachments not provided with the product, loss of parts and use at other than the specified voltage. Cutting units and guards are not covered because they wear. To request service, go to www.philips.com/support.

Follow the manufacturer’s safety warnings and check your exact model before using these instructions. Report an error.

Document information and editorial sourcing

The product instructions/information above in this page are based on the original manufacturer document.

Last updated: November 18, 2026

Find more product manuals in:

Related Philips Norelco Manuals